PLANET WNAP-6305 - Manual

Note
– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
2. Installation Precautions
4. Hardware Installation
– 7 – – 8 –
– 5 – – 6 –
WNAP-6305 Quick Guide CD-ROM
PoE Injector
Mounting Tie x 2
Protective Plug x 2
Power Adapter
150Mbps
802.11n Wireless
Outdoor Access Point
WNAP-6305
FURTHER INFORMATION
The above steps introduce simple installations and
configurations
for WNAP-6305. For further
configurations of different operation modes, please refer
to the user’s manual in the CD. If you have further
questions, please contact the local dealer or distributor
where you purchased this product.
2011-E10420-001
Thank you for choosing PLANET WNAP-6305. Before
installing the AP, please verify the contents inside the
package box.
If there is any item missed or damaged, please
contact the seller immediately.
STEP 1: Push the latch in the bottom of WNAP-6305 to
remove the sliding cover.
STEP 2: Plug the RJ-45 Ethernet cable into the LAN Port
of WNAP-6305.
1. Assign a static IP address to your PC which should be
in the same network segment with the WNAP-6305. As
the default IP address of the WNAP-6305 is
192.168.1.1, you may choose from 192.168.1.2 to
192.168.1.254. Then click OK.
2. Open the web browser on your PC, key in the IP
address (192.168.1.1) of the WNAP-6305 in the
address bar, and then enter.
3. The default User name and Password are both
“admin”. Enter them and then click OK.
4. When you enter into the Web User Interface, click
Setup Wizard at the left hand side of the screen.
Once the basic configuration of the AP is done. Click
Apply button to make the change take effect.
Note
Users MUST use the “Power cord & PoE Injector”
shipped in the box with the WNAP-6305.
Otherwise, the product may be damaged.
3. Physical Introduction
Rear Panel Description – LED Indication
Rear Panel Description – Port & Connector
1. Users MUST use a proper and well-installed surge
arrestor and grounding kit with WNAP-6305;
otherwise, a random lightening could easily cause fatal
damage to WNAP-6305. EMD (Lightning) DAMAGE
IS NOT COVERED UNDER WARRANTY.
2. Users MUST use the “Power cord & PoE Injector”
shipped in the box with the WNAP-6305. Use of other
options will cause damage to the WNAP-6305.
3. Users MUST power off the WNAP-6305 first before
connecting the external antenna to it; otherwise,
damage might be caused to the WNAP-6305 itself.
STEP 4: Take out the power cord and PoE injector, plug
the power cord into the DC port and plug the
other side of the RJ-45 cable in the STEP 2 into
the POE port of the PoE injector.
STEP 3: Slide the cover back and insert the protective
plug to seal the bottom of the WNAP-6305.
STEP 5: Successful installation.
Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Default SSID: default
Connect the WNAP-6305 with your PC by an Ethernet
cable plugging in LAN port of PoE injector in one side and
in LAN port of PC in the other side. Power on the
WNAP-6305 by PoE from PoE injector.
5. Web Login
Power LED WAN Port LED LAN Port LED Wireless LED
WAN Port
(Connect to DSL/Cable Modem)
LAN Port
(Connect to PC via PoE Injector)
RP-SMA Connector
(Connect to External Antenna)
To LAN Switch or PC
To WNAP-6305