PLANET WNAP-7205 User Manual

11a/n wireless outdoor access point, 5ghz, Wnap-7205

Advertising
background image

Note

– 1 –

– 2 –

– 3 –

– 4 –

1. Package Contents

2. Installation Precautions

4. Hardware Installation

– 7 –

– 8 –

– 5 –

– 6 –

WNAP-7205

Quick Guide

CD-ROM

PoE Injector

Mounting Tie x 2

Power Adapter

5GHz

802.11a/n Wireless
Outdoor Access Point

WNAP-7205

FURTHER INFORMATION
The above steps introduce simple installations and
configurations for WNAP-7205. For further configurations
of different operation modes, please refer to the user’s
manual in the CD. If you have further questions, please
contact the local dealer or distributor where you purchased
this product.

2011-E10430-000

Thank you for choosing PLANET WNAP-7205. Before
installing the AP, please verify the contents inside the
package box.

If there is any item missed or damaged, please
contact the seller immediately.

STEP 1: Push the latch in the bottom of WNAP-7205 to

remove the sliding cover.

STEP 2: Plug the RJ-45 Ethernet cable into the LAN Port

of WNAP-7205.

1. Assign a static IP address to your PC which should be

in the same network segment with the WNAP-7205. As
the default IP address of the WNAP-7205 is
192.168.1.1, you may choose from 192.168.1.2 to
192.168.1.254. Then click OK.

2. Open the web browser on your PC, key in the IP

address (192.168.1.1) of the WNAP-7205 in the
address bar, and then enter.

3. The default User name and Password are both

“admin”. Enter them and then click OK.

4. When you enter into the Web User Interface, click

Setup Wizard at the left hand side of the screen.
Once the basic configuration of the AP is done. Click
Apply button to make the change take effect.

Note

Users MUST use the “Power cord & PoE Injector”
shipped in the box with the WNAP-7205.
Otherwise, the product may be damaged.

3. Physical Introduction

Rear Panel Description – LED Indication

Rear Panel Description – Port & Connector

1. Users MUST use a proper and well-installed surge

arrestor and grounding kit with WNAP-7205;
otherwise, a random lightening could easily cause fatal
damage to WNAP-7205. EMD (Lightning) DAMAGE
IS NOT COVERED UNDER WARRANTY
.

2. Users MUST use the “Power cord & PoE Injector”

shipped in the box with the WNAP-7205. Use of other
options will cause damage to the WNAP-7205.

3. Users MUST power off the WNAP-7205 first before

connecting the external antenna to it; otherwise,
damage might be caused to the WNAP-7205 itself.

STEP 4: Take out the power cord and PoE injector, plug

the power cord into the DC port and plug the
other side of the RJ-45 cable in the STEP 2 into
the POE port of the PoE injector.

STEP 3: Slide the cover back to seal the bottom of the

WNAP-7205.

STEP 5: Successful installation.

Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Default SSID: default

Connect the WNAP-7205 with your PC by an Ethernet
cable plugging in LAN port of PoE injector in one side and
in LAN port of PC in the other side. Power on the
WNAP-7205 by PoE from PoE injector.

5. Web Login

Power LED

WAN Port LED

LAN Port LED

Wireless LED

WAN Port

(Connect to DSL/Cable Modem)

LAN Port

(Connect to PC via PoE Injector)

RP-SMA Connector

(Connect to External Antenna)

To LAN Switch or PC

To WNAP-7205

Advertising