PLANET WNAP-7350 User Manual

Web login, Hardware installation

Advertising
background image

Note

– 1 –

– 2 –

– 3 –

– 4 –

1. Package Contents

3. Physical Introduction

2. Installation Precautions

– 7 –

– 8 –

5. Web Login

– 5 –

– 6 –

Mounting Kit x 1

RJ-45 Waterproof Kit x 2

FURTHER INFORMATION:
The above steps introduce simple installations and
configurations for WNAP-7350. For further configurations of
different operation modes, please refer to the user’s manual
in the CD. If you have further questions, please contact the
local dealer or distributor where you purchased this product.

2011-E10510-000

Thank you for choosing PLANET WNAP-7350. Before
installing the AP, please verify the contents inside the
package box.

If there is any item missed or damaged, please
contact the seller immediately.

Rear Panel Description – Port & Connector

STEP 4: Plug the other waterproof kit to the WAN/LAN

port to complete the installation.

STEP 3: Take out the power cord and PoE injector, plug

the power cord into the DC port and plug the
other side of the RJ-45 cable into the POE port of
the PoE injector.

STEP 1: Plug the N-Type (M) to N-Type (M) RF cables into

the antenna connectors of the WNAP-7350, and
then connect the N-Type (F) antennas to the
other side of the RF cables.

Connect the WNAP-7350 with your PC by an Ethernet cable
plugging in LAN port of PoE injector in one side and in LAN
port of PC in the other side. Power on the WNAP-7350 by PoE
from PoE injector.

1. Assign a static IP address to your PC which should be in

the same network segment with the WNAP-7350. As
the default IP address of the WNAP-7350 is
192.168.1.1, you may choose from 192.168.1.2 to
192.168.1.254. Then click OK.

2. Open the web browser on your PC, key in the IP

address (192.168.1.1) of the WNAP-7350 in the
address bar, and then enter.

3. The default User name and Password are both

“admin”. Enter them and then click OK.

Default IP Address: 192.168.1.1

Default User name: admin

Default Password: admin

Default SSID: default

PoE Injector & Power Cord

Quick Guide

WNAP-7350

Quick Installation Guide

300Mbps 802.11a/n

Wireless Outdoor AP

CD-ROM

WNAP-7350

1. Users MUST use a proper and well-installed surge

arrestor and grounding kit with WNAP-7350; otherwise, a
random lightening could easily cause fatal damage to
WNAP-7350. EMD (Lightning) DAMAGE IS NOT
COVERED UNDER WARRANTY
.

2. Users MUST use the “Power cord & PoE Injector” shipped

in the box with the WNAP-7350. Use of other options will
cause damage to the WNAP-7350.

3. Users MUST power off the WNAP-7350 first before

connecting the external antennas to it; otherwise,
damage might be caused to the WNAP-7350 itself.

4. Now, you can see the Web management UI of the

WNAP-7350.

You can use Easy Setup at the top of the screen to

configure the WNAP-7350.

4. Hardware Installation

N-Type (F)

N-Type (F) LAN (802.3af PoE)

WAN/LAN

STEP 5a: Pole Mounting
(a.1) Attach the mounting bracket to the back of the

device by using four screws and flat washers.

(a.2) Assemble the M bracket to the outside of the

mounting bracket by using four screws and flat
washers.

(a.3) Install the mounting bracket assembly to the pole

by using the toothed bracket, and then tighten it by
four long screws.

STEP 5b: Wall Mounting
(b.1) Attach the mounting bracket to the back of the

device by using four screws and flat washers.

(b.2) Assemble the M bracket to the wall by using four

screws and flat washers.

(b.3) Install the mounting bracket assembly inside the M

bracket mounted in the wall by using four screws
and flat washers.

IMPORTANT SAFETY PRECAUTIONS:

1) LIVES MAY BE AT RISK! Please be aware for

the electric wires around, and tighten the
pole. Carefully read the section "OUTDOOR
INSTALLATION WARNING"
in the manual
before installation.

2) Users MUST use the “Power cord & PoE

Injector” shipped in the box with the
WNAP-7350. Otherwise, the product might be
damaged.

STEP 2: Plug the RJ-45 Ethernet cable into the LAN Port of

WNAP-7350 through the waterproof kit.

(a.1)

(a.2)

(a.3)

(b.1)

(b.2)

(b.3)

Note

Caution

Pole diameter less than 5cm may require the use
of hex nuts to lock the long screws to the
suitable location.

Advertising