PLANET WNAP-C3220 User Manual

300mbps, Wnap-c3220, Web login 5. wireless network connection

Advertising
background image

Note

– 1 –

– 2 –

– 3 –

– 4 –

1. Package Contents

2. Physical Installation

3. Hardware Installation

– 7 –

– 8 –

4. Web Login

5. Wireless Network Connection

– 5 –

– 6 –

Front Panel Description

Rear Panel Description

Wireless AP

Quick Guide

CD-ROM

Power Adapter

Mounting Kit

Ethernet Cable

300Mbps

802.11n Wireless Ceiling Mount
Range Extender / Access Point

WNAP-C3220

FURTHER INFORMATION
The above steps introduce simple installations and
configurations for WNAP-C3220. For further configurations of
different operation modes, please refer to the user’s manual in
the CD. If you have further questions, please contact the local
dealer or distributor where you purchased this product.

2011-E10400-000

Thank you for choosing PLANET WNAP-C3220. Before
installing the AP, please verify the contents inside the
package box.

If there is any item missed or damaged, please
contact the seller immediately.

Step 1: Attach the bracket to the wall or ceiling, and

mark each point in the bracket for the screws.
Remove the bracket to drill the points and insert
the plastic wall-mounts. Use screws to lock the
bracket by a screw driver.

Step 3: Plug the power adapter into the WNAP-C3220.

If WNAP-C3220 is connected to a 802.3af PoE
switch in STEP 2, you don’t have to plug the
power adapter.

Step 4: Attach the

WNAP-C3220 to the
mounting bracket.

Step 5: Successful

installation.

Step 2: Plug the RJ-45 Ethernet cable into the

WNAP-C3220.

Step 4: Once the basic configuration of the AP is done.

Click Save button to make the change take
effect.

Step 3: When you enter into the Web User Interface,

click Setup Wizard at the left hand side of the
screen.

1. Click “Start” button located at lower-left corner of you

computer

2. Click “Control Panel”
3. Double click “Network and Sharing Center” icon
4. Click “Change adapter settings”
5. Double click “Local Area Connection”
6. Select “Internal Protocol Version 4 (TCP/IPv4)”

and click “Properties”

7. Select “Use the following IP address”
8. Assign a static IP address to your PC which should be

in the same network segment with the WNAP-C3220.
As the default IP address of the WNAP-C3220 is
192.168.1.1, you may choose from 192.168.1.2 to
192.168.1.254. Then click OK.

Step 1: Set your computer to a static IP address.

(Following steps are based on Windows 7)

Step 2: The Web management allows you to access and

manage the Wireless AP easily. Launch the Web
browser and enter the default IP address
http://192.168.1.1

The default User name and Password are both “admin”.
Then click OK button to continue.

Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Default SSID: default

A computer with wired Ethernet connection to the
WNAP-C3220 is required for the first-time configuration.

Note

1. ONLY use the power adapter supplied with

WNAP-C3220. Otherwise, the product may be
damaged.

2. For the power supply of WNAP-C3220, you

could use either IEEE 802.3af PSE device or
12VDC Adapter. Please do not use 12V
adapter and PSE devices at the same time. It
may damage the WNAP-C3220 itself.

Step 1: Right-Click on the network icon displayed in the

system tray.

Step 2: Highlight the wireless network (SSID) to connect

and click [Connect].

Step 3: Enter the encryption key of the Wireless Access

Point.

x 4

x 4

1 x 10/100/1000Mbps PoE LAN Port

Reset Button

Power Connector 12V DC Input

Power LED

Advertising