PLANET WNRT-633 - Manual

Note
– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
3. Hardware Installation
2. Physical Introduction
– 7 – – 8 –
4. Wired Network Configuration (Windows 7) 5. Enter into the Web Management
– 5 – – 6 –
Front Panel Description
Rear Panel Description
Wireless Router Quick Guide CD-ROM
Ethernet Cable 5dBi Antennas
The above steps introduce simple installations and configurations
of the WNRT-633. For further configurations of WAN, LAN,
Wireless, Firewall, Virtual Server, Security, Routing, DMZ, DDNS,
etc, please refer to the user’s manual in the CD. If you have further
questions, please contact the local dealer or distributor where you
purchased this product.
2011-E50300-000
Thank you for choosing PLANET WNRT-633. Before installing the
router, please verify the contents inside the package box.
The WNRT-633 should contain the following items in the package:
If there is any item missing or damaged, please
contact the seller immediately.
STEP 1: Locate the Wireless Router in an optimum place, and
adjust the antenna for the best coverage.
6. Wireless Network Connection
Further Information
STEP 1: Right-Click on the network icon displayed in the
system tray.
STEP 2: Connect the Power Adapter provided in the package
to the Wireless Router. The power LED (PWR) on the
front panel will turn on accordingly.
STEP 3: Follow the figure below to connect the network
devices. It depends on your network environment to
connect the WAN port to a Cable/xDSL modem, or the
Ethernet directly in your place.
A computer with wired Ethernet connection is required for the
first-time configuration of the Wireless Router.
Set your computer to get an IP address from the Wireless
Router:
1. Click “Start” button located at the lower-left corner of your
computer.
2. Click “Control Panel”.
3. Double click “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double click “Local Area Connection”.
6. Select “Internal Protocol Version 4(TCP/IPv4)” and
click “Properties”.
7. Select “Obtain an IP Address automatically” and
“Obtain DNS Server Address automatically”, and then
click “OK” button twice to save the configuration.
Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Default SSID: WNRT-633
Default Wireless Encryption Type: None
STEP 3: Enter the encryption key of the Wireless Router if
necessary.
STEP 1: The Web management allows you to access and
manage the Wireless Router easily. Launch the Web
browser and enter the default IP address
http://192.168.1.1
WNRT-633
Quick Installation Guide
300Mbps 802.11n Wireless
Gigabit Broadband Router
12V/1A Power Adapter
WAN WLAN 1 2 3 4 PWR WPS
WNRT-633
WAN Wireless
WPS Power LAN1~LAN4
Cable
Modem
PC
Ethernet Cable
Ethernet Cable
Power
Power
Adapter
WNRT-633
Line
ADSL Phone
Phone
Splitter
Internet
Telephone wire
1
2
For security reasons it is recommended to change the password
at the first login and memorize it.
STEP 2: When the login window pops up, please enter the User
Name and Password. The default User Name and
Password are both “admin”.
Then click OK button to continue.
STEP 2: Highlight the wireless network (SSID) to connect and
click [Connect] button.
You have already finished the configuration of the WNRT-633.
Now you can use your iPhone, iPad, laptop, and any other Wi-Fi
device to connect with it wirelessly and start surfing the
internet.
STEP 4: Once the basic configuration of the router is done.
Click “Finished” button for the change to take effect.
STEP 3: After you enter into the Web User Interface, click
Wizard at the left hand side of the screen.
Please follow the indications on the screen to
quickly set up for the Internet connection.
5 dBi Antenna
Power WPS/Reset 4 x Gigabit LAN Ports Gigabit WAN Port
Power