BOSS VE-8 Acoustic Singer - Manual (Page 13)

13
English
Deutsch
Français
Italiano
Español
Português
Nederlands
Advanced Settings
Restoring the Factory Settings
(Factory Reset)
Here’s how to return the VE-8 to its factory-set state.
1 While holding down the (GUITAR) REVERB [TYPE] and
CHORUS [TYPE] button, turn on the power.
“ Fr ” appears in the display, and the [MEMORY] button blinks.
* If you decide to cancel the factory reset, turn off the power.
2 Press the [MEMORY] button.
The display flashes and the factory reset is executed.
* Never turn off the power while Factory Reset is in progress.
3 Once “ oK ” appears in the display, you can turn off
the power.
System Settings
Settings that are shared by the entire VE-8 are called “system
settings.”
1 Hold down the [MEMORY] button and press the
[HARMONY] pedal.
The [MEMORY] button and [HARMONY] pedal are lit red; the VE-8
is in system setting mode.
2 Press the [MEMORY] button to select a parameter
(refer to table).
MEMO
To return to the previous parameter, hold down the [EXIT]
button and press the [MEMORY] button.
3 Use the [?] [=] buttons to select a value.
4 Press the [EXIT] button to exit settings mode.
Parameter Value Explanation
External Footswitch Setting
C1 (C1)
C2 (C2)
Specifies the functions of the external footswitch
(C1, C2) connected to the MEMORY =? jack.
& “Connecting a Footswitch” (p. 6)
1 MEMORY = (C1: default)
2 MEMORY ? (C2: default)
3 LOOP STOP (HOLD: CLEAR)
4 LOOPER SOURCE
5 GUITAR ACOUSTIC RESONANCE SW
6 GUITAR CHORUS (EFFECT) SW
7 GUITAR REVERB SW
8 VOCAL ENHANCE SW
9 VOCAL HARMONY (EFFECT) SW
10 VOCAL REVERB SW
11 KEY UP
12 KEY DOWN
13 MEMORY/MANUAL
14 TAP TEMPO
15 TUNER ON/OFF
Pedal Setting
1M (C1 Mode)
2M (C2 Mode)
CP (CHORUS)
hP (HARMONY)
Specifies how pedals behave when pressed.
1
MOMENTARY
The effect turns on only while the pedal
is pressed.
2
TOGGLE
The effect switches with each press of the
pedal (default).
MEMORY Pedal Hold Setting
MP (MEMORY
Pedal)
With the default setting, tuner or bypass is
selected when you long-press a MEMORY =?
pedal, but you can change this so that memory
numbers are consecutively switched instead.
0 TUNER, BYPASS (default)
1
Memory numbers are switched
consecutively
Looper Setting
LP (LOOP)
Specifies the switching order of the Looper.
1 REC 0 PLAY 0 DUB (default)
2 REC 0 DUB 0 PLAY
NOTCH/PHASE Setting
nP (NOTCH/
PHASE)
If you want the NOTCH/PHASE setting to be
maintained even after switching memories,
choose the “2 (SYSTEM)” setting.
1 MEMORY (default)
2 SYSTEM
Startup Mode
SM (Startup
Mode)
Selects the mode at power-on.
1 MANUAL MODE (default)
2 MEMORY MODE
3 MEMORY STOMP MODE
Auto Off Setting
Ao (Auto Off)
With the factory settings, the VE-8 will
automatically be switched off 10 hours after you
stop playing or operating the unit.
* If you don’t want the unit to turn off
automatically, change this setting to “ 0 ”
(OFF).
0 The power will not turn off automatically.
1
The power will automatically turn off when
10 hours. (default)