Document Outline

• Product Summary
  • SuperBus 2000 vs. SuperBus
• Module Components
  • Figure 1. Module Circuit Board Components
  • Table 1. Module Component Descriptions
• Component
• Function
  • Installation Guidelines
    • Table 2. Maximum Bus Devices Per Panel
• Panel
• Maximum Bus Devices
  • Table 3: Maximum Wire Lengths
• Panel
• Maximum Wire Length
  • Tools and Supplies Needed
  • Installation
    • Mounting the Module
      • To Mount the Module on a Wall
        • 1. Remove the module cover and set it aside (Figure 2).
          • Figure 2. Removing the Cover
        • 2. Place the back-plate on the wall and mark the three mounting holes (Figure 3).
        • 3. Drill holes and insert appropriate anchors.
        • 4. Secure the back-plate to the wall with included screws.
          • Figure 3. Wall Mounting Hole Locations
      • To Mount the Module in an Advent Cabinet
        • 1. Remove AC panel power and disconnect the backup battery(s).
        • 2. Remove the module cover and set it aside (Figure 2).
        • 3. Turn the module upside down and line up the holes on the back-plate at the desired location (F...
        • 4. Secure the back-plate to the cabinet using three 1/4 - inch #6-32 self-tapping screws (not inc...
          • Figure 4. Mounting the Module in an Advent Cabinet
      • To Mount the Module in a Concord Cabinet
        • 1. Remove AC panel power and disconnect the backup battery.
        • 2. Remove and discard the module cover (Figure 2).
        • 3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board.
          • Figure 5. Support Standoff
        • 4. Slide the module back-plate onto the two clips located on the top-left corner or center of the...
        • 5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).
        • 6. Gently press the module up and onto the cabinet side tab.
          • Figure 6. Mounting the Module in a Concord Cabinet
  • Wiring the Module
    • To Wire the Module to a Panel
      • 1. Make sure the panel AC power is turned off or removed, and the panel backup battery(s) are dis...
      • 2. Wire the module to the panel as shown in Figure 7 and explained in Table 4.
        • Figure 7. General Module Wiring
      • Table 4. SuperBus Module/Panel Wiring
• Module
• Terminals
• Advent*
• Ultra-
• Gard
• Concord
  • To Wire Detectors to the Module
    • Table 5. Zone Input Wire Runs
• Gauge
• Max. Wire Run*
  • 1. Figure 8 shows an example of how to connect up to eight normally closed (N/C) or normally open...
    • Figure 8. Connecting N/C and N/O Intrusion Circuits to the Module
  • Installing a Cover Tamper Switch
    • To install the tamper reed switch (Figure 9):
      • 1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Fi...
      • 2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...
      • 3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module...
        • Figure 9. Installing the Reed Switch
  • Setting the Module Unit Numbers
    • On Concord (software versions 1.0–1.6) and UltraGard Panels
      • Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels)
    • On Concord (software versions 2.0 or later) and Advent Panels
  • Power Up and Bus Communication
    • On Concord and Advent Panels
    • New Installations
      • 1. Verify that all wiring between the panel and module is correct.
      • 2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...
      • 3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on an...
    • Existing Installations
      • 1. Verify that all wiring between the panel and module is correct.
      • 2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...
      • 3. Press 8 for System Menu.
      • 4. Press 0 for Program Menu.
      • 5. Enter your Install Code (default 0123).
      • 6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added...
      • 7. Press * twice to return to the Main Menu.
      • 8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the...
    • On UltraGard Panels
      • 1. Verify that all wiring between the panel and module is correct.
      • 2. Verify nonconflicting bus device unit number settings.
      • 3. Connect the panel backup battery and restore panel AC power.
      • 4. Turn on the panel AC power.
      • 5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM.
  • Programming and Testing
  • Troubleshooting
    • Table 6. Troubleshooting
• Problem
• Action/Solution
  • 1. Check for incorrect wiring connections.
  • 2. Make sure panel AC power is applied and the backup battery(s) are connected.
  • 3. If the LED still remains off, replace the module.
  • 1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...
  • 2. Check for incorrect wiring connections.
  • 3. For Concord (software versions 1.0–1.6) and UltraGard panels make sure that module DIP switch ...
  • 4. If the LED still doesn’t flash, replace the module.
  • 1. For Concord (software versions 1.0–1.6) or UltraGard systems, check for bus devices with the s...
  • 2. Re-initialize the panel by disconnecting and reconnecting panel power.
  • 3. Make sure the zone has been “learned” into panel memory.
  • 4. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...
  • 5. Remove zones and try installing the module without the zones.
  • 6. Replace the module.
  • Specifications
  • Notices