Document Outline

• 1. INTENDED USE
• 2. PRECAUTIONS
  • 2.1. Maintenance
  • 2.2. Accumulator / battery pack
    • 2.2.1. Power supply of weighing indicators in plastic casings
    • 2.2.2. Replacement of worn batteries
  • 2.3. Operation in a strong electrostatic field
• 3. WARRANTY CONDITIONS
• 4. MAIN DIMENSIONS
  • 4.1. Table scales WPT/F series
  • 4.2. Waterproof scales of WPT/H series
  • 4.3. Waterproof scales of WPT/HR series
  • 4.4. Scales of WPT series
• 5. UNPACKING AND ASSEMBLY
  • 5.1. Table scales of WPT/F series
  • 5.2. Scales of WPT series
  • 5.3. Waterproof scales of WPT/H, WPT/HR series
• 6. GETTING STARTED
• 7. KEYPAD
• 8. KEYS’ FUNCTIONS
• 9. INSCRIPTIONS ON THE DISPLAY
• 10. USER MENU
  • 10.1. Submenus
  • 10.2. Browsing user menu
    • 10.2.1. Keypad
    • 10.2.2. Return to the weighing mode
• 11. WEIGHING
  • 11.1. Tarring
  • 11.2. Inscribing tare value
  • 11.3. Zeroing
  • 11.4. Weighings in two ranges
  • 11.5. Selection of basic weight unit
  • 11.6. Temporarily selected unit
• 12. MAIN PARAMETERS
  • 12.1. Setting a filtering level
  • 12.2. Median filter
  • 12.3. Autozero function
  • 12.4. Tare function
• 13. RS 232 PARAMETERS
  • 13.1. Printout type
  • 13.2. Minimal mass threshold
  • 13.3. Baud rate
  • 13.4. Serial transmission parameters
• 14. OTHER PARAMETERS
  • 14.1. Backlight function
    • 14.1.1. Backlight for supplying from mains
    • 14.1.2. Backlight for supplying from batteries
  • 14.2. “Beep” signal – after pressing a key
  • 14.3. Automatic switch-off
  • 14.4. Battery voltage level check
    • 14.4.1. Checking the batteries
    • 14.4.2. Battery discharge pictogram
    • 14.4.3. Accumulator charging option
    • 14.4.4. Formatting rechargeable battery packs
• 15. WORK MODES
  • 15.1. Setting accessibility of operation modes
  • 15.2. Selecting quantity of operation modes
  • 15.3. Counting pieces of the same mass
  • 15.4. +/- control referring to the inscribed standard mass
  • 15.5. Control of % deviation referring to the inscribed standard mass
    • 15.5.1. Standard mass determined by its weighing
    • 15.5.2. Mass of standard inscribed to scale memory
  • 15.6. Automatic tare
  • 15.7. Measurement max force on the pan – latch
  • 15.8. Totalizing
    • 15.8.1. Enabling the work mode
    • 15.8.2. Totalizing procedure
    • 15.8.3. Memory of the last value of sum of weighed goods
    • 15.8.4. Return to weighing
  • 15.9. Weighing animals
  • 15.10. Tare memory
    • 15.10.1. Entering the tare value to the scale memory
    • 15.10.2. Selecting a tare value from the memory
• 16. USER CALIBRATION
  • 16.1. Calibration
  • 16.2. Start mass adjustment
• 17. COOPERATION WITH PRINTER
• 18. COOPERATION WITH COMPUTER
• 19. COMMUNICATION PROTOCOL
  • 19.1. General information
  • 19.2. A set of commands for RS interfaces
  • 19.3. Respond message format
  • 19.4. Command’s description
    • 19.4.1. Zeroing
    • 19.4.2. Tarring
    • 19.4.3. Get tare value
    • 19.4.4. Send the stable result in basic unit
    • 19.4.5. Send the result immediately in basic unit
    • 19.4.6. Send the stable result in current unit
    • 19.4.7. Send the result immediately in current unit
    • 19.4.8. Switch on continuous transmission in basic unit
    • 19.4.9. Switch off continuous transmission in basic unit
    • 19.4.10. Switch on continuous transmission in current unit
    • 19.4.11. Switch off continuous transmission in current unit
    • 19.4.12. Send all implemented commands
  • 19.5. Manual printouts / automatic printouts
  • 19.6. Continuous transmission
  • 19.7. Configuring printouts
• 20. ERROR COMMANDS
• 21. TECHNICAL PARAMETERS
  • 21.1. Scales of WPT series
  • 21.2. Table scales of WPT/F series
  • 21.3. Waterproof scales of WPT/H series
  • 21.4. Waterproof scales of WPT/HR series
• 22. TROUBLE SHOOTING
• 23. ADDITIONAL EQUIPMENT