Marantz MV8300_U1B - Manual (Page 17)

EN
17
5 Enter cable box brand
Press %fi to move
the arrow to
“BRAND”.
Press
@ # to enter the
brand code from the
list shown to the
right.
6 Engage test mode
Press %fi to move the arrow to “TEST MODE”,
then press OK.
NOTE:
If you do not engage the test mode in step 6 , “INPUT
CH” and “BRAND” are not set.
● If the cable box’s
channel changes
to 9, setting is
complete
Press
@ # to move
the arrow to
“YES”, then press
OK and “CABLE
BOX CONTROL IS ON” appears on the screen
for about 5 seconds.
● If the cable box’s channel does not change to 9
1 Press @ # to move the arrow to “NO”.
2 Press OK.
3 Repeat step 5 until the cable box’s channel
changes to 9 by entering another code.
4 If the channel does not change after going
through all the code numbers listed for your
model of cable box, then try all the other
numbers.
7 Return to normal screen
Press MENU.
CABLE BOX BRAND LIST
BRAND CODE
ARCHER 1, 5, 17
CABLETENNA 1, 17
CABLEVIEW 15, 16, 17, 21, 25
CITIZEN 15, 16, 17, 21, 25
CURTIS 2, 8
DIAMOND 1, 17
GC BRAND 15, 16, 17, 21, 25
GEMINI 15
GENERAL INSTRUMENTS 1, 4, 6, 11, 12, 15, 28
HAMLIN 10, 18, 23
JASCO 15
JERROLD 1, 4, 6, 11, 12, 15, 28
NOVAVISION 2, 8
OAK 7, 20
PANASONIC 13, 14
PULSER 15, 16, 17, 21, 25
RCA 13, 14
REGAL 10, 18, 23
REMBRANDT 1, 16, 17
SAMSUNG 5, 16, 24
SCIENTIFIC ATLANTA 2, 8
SIGMA 7, 20
SL MARX 5, 16, 17, 24, 25
SPRUCER 13, 14
STARGATE 5, 15, 16, 17, 21, 24, 25
TELEVIEW 5, 16, 24
TOCOM 1, 4, 16
UNIKA 1, 17
UNIVERSAL 16, 17, 25
VIDEOWAY 3, 9, 22
ZENITH 3, 9, 22
If the VCR’s clock has not been set (with AUTO
CLOCK set to ON)
“CABLE BOX USERS SET CLOCK MANUALLY” appears for
about 5 seconds when you press OK in step 3, then the
Clock Set screen appears.
Perform Manual Clock Set on page 12. If you press MENU
after the clock has been set, the Cable Box Input Channel
screen in step 4 appears.
NOTES:
● The Controller may not work with all types of cable box.
● If your cable box does not respond to any code, you cannot
use the Controller to change cable box channels. In this case,
make sure to leave the cable box turned on and tuned to the
proper channel before the scheduled start time of timer
recording.
Contact your cable company about the possibility of
exchanging your current cable box with the one compatible
with your VCR.
● The VCR can only change the cable box channel through the
Controller during timer recording.
● If your cable box cannot be operated with a Remote (because
it has no remote sensor), you cannot use the Controller to
change its channels. Make sure to leave the cable box turned
on and tuned to the proper channel before the scheduled start
time of timer recording.
● If the VCR’s memory backup expires because of a power
failure, set the cable box input channel and brand again.
● For customers in U.S.A.: If you are unable to set the
Controller, contact JVC toll free at 1-800-252-5722.
FUNCTION SET UP INITIAL SET UP TUNER SET UP
THEN PRESS [OK]
INPUT CH
BRAND 1
TEST MODE
OFF
SELECT WITH ARROW KEYS
SELECT
OK
EXIT
MENU
CABLE SET UP
INPUT CH
BRAND 1
TEST MODE
OFF
FUNCTION SET UP INITIAL SET UP TUNER SET UP
THEN PRESS [OK]
SELECT WITH ARROW KEYS
SELECT
OK
EXIT
MENU
CABLE SET UP
YES NO
DID YOUR CABLE BOX CHANGE TO
CHANNEL 09?
HM-DH40000U-EN15-20 1/22/3, 4:37 PM 17