MITSUBISHI ELECTRIC LT-40133 - Manual (Page 57)

6. NetCommand 57
Before You Begin
1. Connect your A/V devices to the TV and connect
your A/V receiver to the TV and the DVD player.
See chapter 2, “TV Connections,” for suggestions.
2. Open the Inputs > AVR menu.
Note: The terms Input 1–Input 4 used in the AVR
screen are temporary placeholder names that
can be renamed. They refer to the A/V receiver
inputs for which the TV can learn IR codes.
Setup 1: Automatic A/V Receiver Switching to Its
TV Audio Input
Most devices are set up like the VCR in this example, in
which analog audio from the device is sent through the
TV.
Use this setup for:
• Sources providing only analog stereo output, such
as a VCR
• Audio from ANT 1 and ANT 2
57
"/5
."*/
"/5
"69
BV
EJ
P



WJ
EF
P
BVEJP

WJEFP
*ODPNJOH

$PBYJBM

$BCMF
"7
3FDFJWFS
%7%
BVEJP

JOQVU
57
BVEJP

JOQVU
"73
"VEJP
0VUQVU
EJHJUBM
PS

BOBMPH
BVEJP

GSPN
57
WJEFP
BOBMPH
BVEJP 7$3
XJUI

"OBMPH

"VEJP
Setup 1: A/V receiver audio from the TV’s digital or
analog audio output (
DIGITAL AUDIO OUT or AVR AUDIO
OUTPUT)
1. Under Learn/Name, navigate to highlight the area
next to Input 1.
In this example, the IR code for the A/V receiver’s
TV Audio input will be “learned” as Input 1.
2. Press ENTER on the TV’s remote control.
3. While the text Input1 is flashing, press and hold the
TV INPUT key on the A/V receiver’s remote control.
4. When a check appears next to Input 1, release the
TV INPUT key.
Setup to Control Automatic Switching of
A/V Receiver Audio Inputs
Two different setups are described here:
Setup 1: Automatic A/V Receiver Switching to TV
Audio Input.
Setup 2: Automatic A/V Receiver Switching for a
device sending audio directly to the A/V receiver.
• Audio Available from TV only: Use Setup 1.
Audio from ANT 1 and ANT 2 must be sent to the
A/V receiver from the TV’s DIGITAL AUDIO OUT or
analog AVR AUDIO OUTPUT.
Use Setup 1 to make the A/V receiver switch to
its designated TV audio input when viewing these
sources.
• HDMI Digital Stereo Audio: Use Setup 1.
Digital stereo audio from an HDMI connection
is available both in digital format (from the TV’s
DIGITAL AUDIO OUT) jack and in analog format
(from the TV’s
AVR AUDIO OUTPUT jack).
• Analog Stereo Audio: Use Setup 1.
Audio from sources with only analog stereo output
(such as a VCR) can be sent either directly to the
A/V receiver or through to the TV and then on to the
A/V receiver.
Mitsubishi recommends you send audio through
the TV as shown in the example. Setup 1 causes
the A/V receiver to switch to its input designated for
TV audio.
If you have a digital A/V receiver, the TV makes the
audio available by converting analog audio to a
digital output.
• Digital Surround Sound: Use Setup 2.
A device can send digital surround sound such as
Dolby Digital or DTS directly to the A/V receiver,
bypassing the TV entirely. The device might be
a DVD player, cable box, or satellite receiver, and
could have HDMI output. A DVD player is used in
this example.
Your setup may include additional devices with
digital surround sound connected directly to the
A/V receiver. These devices might be a DVD player
plus a cable box or satellite receiver.
Setting Up NetCommand Control of
an A/V Receiver, continued
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
• physically connected the TV to the A/V receiver
• selected the A/V receiver for audio. Press
AUDIO, then to show the Speakers option,
then to select the A/V Receiver.
• “learned” the IR codes for the A/V receiver
inputs
• chosen the correct input in the NetCommand
A/V Receiver Learn screen