Jotul GF 100 DV II - Manual (Page 22)

22
GF 100 DV II Nordic QT
GF 200 DV II Lillehammer
Maintenance
This appliance and its venting system should be in-
spected before use and at least annually by a qualified
service technician.
IMPORTANT:
ALWAYS TURN OFF THE GAS SUPPLY TO THE STOVE BEFORE
ANY SERVICE WORK IS PERFORMED ON THE STOVE.
Vent System: The vent components should be inspected
annually to confirm it is clear of obstructions and all
connections are secure. Any joints disconnected must be
resealed using high temperature sealant when reas-
sembled.
Firebox Cleaning: The firebox should be vacuumed
annually to remove any surface build up. Be sure to
vacuum or wipe off the pilot assembly and burner orifice
and burner tube. Handle the logset carefully as it is very
fragile.
Glass Cleaning: Use warm water and a soft cloth. Do not
use abrasive cleaning agents or strong detergents on the
glass. Be sure the glass is cool before cleaning.
Gasket Inspection: Inspect the glass gasket at least
annually. Examine the ribbon gasket for signs of deterio-
ration and make sure the gasket has a positive seal.
Replace the gasket if it appears worn or damaged. Refer
to the replacement parts list on page 27.
Glass and Gasket Replacement
Only Use Replacement Kit 155599.
1. Use a small screwdriver to pry the four retainer clips off
of the glass frame. See fig. 33.
2. Peel away all remnants of the old gasket material and
clean any adhesive residue off the glass.
3. Peel the paper backing off the replacement gasket to
expose the adhesive.
4. Apply the gasket to the panel, wrapping the adhesive
side down around the panel edge. See fig. 34.
5. Insert the gasketed glass panel into the frame and
press the retainer clips back into place as shown.
Operation
Familiarize yourself with the controls of your stove. Make
sure that anyone else using the appliance is also familiar
with the controls and operation procedures. Always
follow the Lighting Instructions on the inside back cover
of this manual and also located on the Rating Plate
attached to the burner assembly.
1. Once the pilot is lit, burner operation is controlled by
the rocker switch located at the left rear corner of the
stove. Use the T-STAT position for the optional thermo-
static or remote control functions. See fig. 32.
2. During the first few fires, you may notice odor and/or
smoke from the stove. This is normal and results from
burn-off of manufacturing residue and curing of
materials. You may find it helpful to provide addi-
tional ventilation and fresh air to alleviate this condi-
tion.
3. Condensation may occur on the glass upon each
lighting of the appliance. This “fog” will disappear as
the appliance heats up.
4. Keep the controls and the area under the appliance
free of debris, vacuum this area frequently. Always
keep the appliance area clear and free from combus-
tible materials, gasoline and other flammable liquids.
If a vacuum is used during any service on the stove,
ALWAYS be sure the stove is cold and there are NO
hotembers or sparks.
5. This appliance has a continuous burning pilot flame.
Exercise caution when using products having combus-
tible vapors. Always shut-off gas supply while servic-
ing the stove.
6. CAUTION: DO NOT OPERATE THIS APPLIANCE WITH
THE GLASS REMOVED CRACKED OR BROKEN. Replace-
ment of the glass should be done by a licensed or
qualified service person. Use only replacement glass
provided by your authorized Jøtul dealer. Never use
any substitute materials.
WARNING: OBSERVE CAUTION WITH THE GLASS. THE
GLASS PANEL MAY SHATTER UNEXPECTEDLY IF STRUCK
WITH AN OBJECT. ALWAYS HANDLE THE GLASS PANEL
WITH CARE. WHEN SERVICING THE STOVE ALWAYS
PULL THE GLASS ASSEMBLY STRAIGHT UP FOR RE-
MOVAL.
7. Clean the glass only when necessary. Wipe surface
with a clean, damp soft cloth. Follow with a dry, soft
towel as desired. Take care not to scratch the glass
surface.
WARNING: DO NOT USE ABRASIVE CLEANERS ON THE
GLASS. NEVER CLEAN THE GLASS WHEN IT IS HOT.
Figure 32. Burner Control Switch location.