JVC DR-MV1B - Manual (Page 45)

Masterpage:Right+
EN
45
Filename [DR-MV1SEK_06DVD Operation2.fm]
Page 45 April 15, 2004 3:30 pm
OPERATIONS ON DVD DECK
You can programme this unit to timer-record as many as
8 programmes.
With the VIDEO Plus+ system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognise.
You can use the remote control to enter the PlusCode number.
1
Load a recordable disc.
2
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3
Press VIDEO Plus+ to access the VIDEO Plus+ screen.
4
Press the number keys to
enter the PlusCode number of a
programme you wish to record,
then press ENTER.
● If you have made a mistake, press
CANCEL (&) and input the correct
number before you press ENTER.
● To clear all entered numbers at a
time, press CLEAR(8).
● If the number you entered is invalid, “PlusCode NO. ERROR
CONFIRM PlusCode NO. THEN RETRY” appears on the TV screen.
Input a valid PlusCode number.
● If “GUIDE PROGRAMME IS NOT SET SELECT CHANNEL YOU
WANT TO RECORD” appears on the TV screen, set Guide Program
numbers manually. (
੬ pg. 83)
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMME” appears on the TV screen, you need to cancel some
of the reserved programmes. (
੬ pg. 49)
5
The PlusCode number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
programme data.
● To cancel this setting, press VIDEO Plus+ or RETURN.
6
Press w e to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “STOP” (To advance/go back the stop time by 30 minutes, press and
hold rt).
● “DAILY/WEEKLY” ( ੬ pg. 45, “Daily/Weekly Recording”)
● “REC MODE” ( ੬ pg. 42, “Recording Mode”)
● “NAME” ( ੬ pg. 61, “Modify Programme Name”)
● “VPS/PDC” ( ੬ pg. 57, “PDC Recording”)*
* VPS (Video Programme System) recording is not currently available
in the U.K. and not possible with this unit.
7
Press ENTER to access the Programme Confirmation screen.
8
Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 8.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 49.
9
Press DVD TIMER (#) to engage the unit’s timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. Press 1 to turn off the unit. When the
VCR deck is in timer standby mode, the unit is automatically turned
off.
● To disengage the timer mode, press DVD TIMER (#) again.
NOTES:
● There may be cases that VIDEO Plus+ Timer Programming function
prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with VIDEO Plus+ Timer Programming function, the beginning of the
second one may be left off the recording.
● VIDEO Plus+ Timer Programming is not possible on the discs used
exclusively for On-Disc Timer Programming.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Daily/Weekly Recording
You can record programmes with one of the following weekly/daily
timer settings.
WEEKLY : Select to record a weekly programme.
MON–FRI : Select to record a daily programme from Monday
through Friday.
MON–SAT : Select to record a daily programme from Monday
through Saturday.
SUN–SAT : Select to record a daily programme from Sunday
through Saturday.
VIDEO Plus+ ® Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “VIDEO Plus+
® System Setup” (
੬ pg. 83) and
set the Guide Program number correctly.
1
4
7
2
5
8
0
3
6
9
0 – 9
RETURN
ENTER
VIDEO Plus+
CLEAR (8)
CANCEL (X)
DVD TIMER (#)
VCR/DVD
SAT
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
programme number has been changed, the wrong programme
number will be displayed on the VIDEO Plus+ programme screen in
step 5. When this happens, set the correct Guide Program number
for that station. (
੬ pg. 83, “VIDEO Plus+
® System Setup”)
Satellite Receiver Users
To timer-record a satellite broadcast using the VIDEO Plus+
system:
A Perform “Satellite Receiver Control Setting (DVD Deck Only)”
(
੬ pg. 23).
B Perform “VIDEO Plus+ ® Timer Programming” ( ੬ pg. 45).
C Leave the satellite receiver’s power on.
DR-MV1SEK_00.book Page 45 Thursday, April 15, 2004 3:30 PM