JVC DR-MV1B - Manual (Page 50)

Filename [DR-MV1SEK_06DVD Operation2.fm]
Masterpage:Left+
50
EN
Page 50 April 22, 2004 5:08 pm
OPERATIONS ON DVD DECK
This function allows you to automatically record a satellite
programme which is timer-programmed on your external satellite
receiver. Connect a satellite receiver to the unit’s L-2 IN/
DECODER connector and programme the timer on the satellite
receiver. When the signals come into the unit from the satellite
receiver, the unit automatically turns on and starts recording.
1
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
2
Set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO”.
( ੬ pg. 74)
● Also refer to “IMPORTANT” on page 78.
3
Press REC MODE repeatedly to set the recording mode.
4
Press and hold SAT# on the unit for about 2 seconds to engage
the Automatic Satellite Programme Recording mode. “SAT#” lights
up on the front display panel and the VCR deck is automatically
selected.
5
Press 1 to turn off the unit.
● “SAT#” is displayed on the front display panel.
NOTES:
● To disengage the Automatic Satellite Programme Recording mode,
press SAT#.
● If the unit’s power is off, it is not possible to engage the Automatic
Satellite Programme Recording mode.
● In step 4, if “SAT#” blinks quickly on the front display panel even
though your satellite receiver’s power is off, Automatic Satellite
Programme Recording will not work properly with that satellite
receiver*. If this is the case, perform “Manual Timer Programming”
(
੬ pg. 46) to timer-record a satellite programme.
* Some satellite receivers output signals even if the power is off.
Automatic Satellite Programme Recording is not possible with those
satellite receivers.
● “SAT#” blinks on the front display panel while Automatic Satellite
Programme Recording is in progress.
● For timer programming of the satellite receiver, refer to the instruction
manual of the satellite receiver.
● Automatic Satellite Programme Recording is not possible if your
satellite receiver does not have a timer.
● Pressing the unit’s 1 button while Automatic Satellite Programme
Recording is in progress turns off the unit’s power and disengages
the Automatic Satellite Programme Recording mode.
● If there are more than one satellite programmes you wish to record
with Automatic Satellite Programme Recording, it is not possible to
set different recording modes for each programme.
● Depending on the type of satellite receiver, the unit may not record a
slight portion of the beginning of the programme or may record
slightly longer than the actual length of the programme.
● If you engage the Automatic Satellite Programme Recording mode
when the satellite receiver’s power is on, the unit will not start
Automatic Satellite Programme Recording even though “SAT#”
blinks on the front display panel. When the satellite receiver shuts off
once and is turned back on again, the unit starts recording.
● Just Clock ( ੬ pg. 86) does not work when the Automatic Satellite
Programme Recording mode is engaged.
● You can also record a programme from your cable system in the
same way if the system has a timer.
About the Automatic Satellite Programme Recording
indicator on the front display panel
When the DVD deck is in the Automatic Satellite Programme
Recording standby mode while the VCR deck is used, the following
indicator lights up instead of “SAT#” as illustrated.
Automatic Satellite Programme
Recording (DVD Deck Only)
ATTENTION:
● When you record programmes by connecting to a digital terrestrial
receiver (Freeview receiver or similar), perform the same steps as
“Automatic Satellite Programme Recording (DVD Deck Only)”
(
੬ pg. 50). It is not possible to operate the digital terrestrial
receiver (Freeview receiver or similar) by using the provided
satellite controller.
● Be sure not to turn on the satellite receiver before the programme
is executed; otherwise, the unit will start recording when the
satellite receiver’s power is turned on.
● If you have connected another appliance other than a satellite
receiver to the L-2 IN/DECODER connector, be sure not to engage
the Automatic Satellite Programme Recording mode; otherwise,
the unit will start recording when the connected appliance’s power
is turned on.
● Automatic Satellite Programme Recording and timer-recording
cannot be done at the same time.
SAT VCR/DVD REC MODE
1
1
4
7
2
5
8
0
3
6
9
REC MODE
VCR/DVD SAT
● Make sure the satellite receiver is connected to the unit’s L-2 IN/
DECODER connector.
● Programme the timer on the satellite receiver.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
Automatic Satellite
Programme indicator
DR-MV1SEK_06DVD Operation2.fm Page 50 Thursday, April 22, 2004 5:09 PM