Dv dubbing (dvd deck only), Pg. 71 – JVC DR-MV1B User Manual

Page 71

Advertising
background image

Masterpage:Right+

EN

71

Filename [DR-MV1SEK_09Editing.fm]

Page 71

April 15, 2004 3:18 pm

EDITING

You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.

1

Connect a camcorder or DV equipment to the DV IN connector

on the unit’s front panel.

2

Load a DVD-RAM/RW/R disc on the unit.

3

Press PR +/– to set the channel to “DV DUBBING”.

● The “DV DUBBING” controller appears on the TV screen.

● If “

” does not appear on the “DV DUBBING” controller, make

sure the DV equipment is connected correctly.

4

Press w e to select

, then press ENTER.

5

Press rt to select the desired

sound track, then press ENTER.

AUDIO 1

: Select this to record the

original stereo sound played
back on the connected DV
equipment.

AUDIO 2

: Select this to record the

dubbed stereo sound played
back on the connected DV
equipment.

MIX

: Select this to record the sound of both “AUDIO 1” and

“AUDIO 2”.

● Note that this selection is not available when the source programme

is recorded in 16BIT (48 kHz) mode.

6

Press REC MODE repeatedly to set the recording mode.

7

Locate the point from where you want to start dubbing, then

stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9

● To play back in slow speed (1/10 of the normal speed), press 9 to

pause playback, then press 3 or 5.

● To play back frame-by-frame, press 9 to pause playback, then press

9 repeatedly. Each press of 9 advances a frame.

● To change the playback direction, press 3 or 5.

8

Press w e to select

, then press ENTER. The

dubbing starts.

● Playback on the external DV equipment and recording on the unit

should start simultaneously.

● When the playback from the beginning is not possible, the “DV

DUBBING” controller cannot be used. Perform dubbing without using
the “DV DUBBING” controller. (

੬ below)

● To pause dubbing, press w e to select

, then press

ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.

● To clear the “DV DUBBING” controller from the TV screen, press ON

SCREEN.

9

Press 8 on the remote control to stop dubbing.

● Both the unit and the external DV equipment stop dubbing.
NOTES:

● Dubbing copyright guarded programmes is not possible.

● Original DV informations such as the recording date and time are not

recorded.

● The superimposed indication during the operation or dubbing is not

recorded.

● It is not possible to perform dubbing when “VCR]” lights up on the

unit. Press VCR] so that “VCR]” lights off.

Performing dubbing without using the “DV DUBBING”
controller
A Press PR +/– to set the channel to “DV DUBBING”.
B Press REC MODE repeatedly to set the recording mode.
C Start playback on the external DV equipment slightly before the
actual point from where you wish to start dubbing.
D Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control. The dubbing starts.
E When the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.

DV Dubbing (DVD Deck Only)

NOTE:
When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.

VPS/PDC VCD

HDD

DVD

DV HS

BS

+

STANDBY/ON

DVD

S-VIDEO

VIDEO

(MONO) L - AUDIO - R

VCR/DVD

VCR

REMAIN

REC MODE

SLOW

<<

>>

PR

DV IN

SAT

DVD

DVD

DVD

VCR

DUB

F-1

DV IN connector

DV cable

(VC-VDV 204U)

(not provided)

Camcorder

DV connector

Your unit

DV equipment

DR-MV1SEK_00.book Page 71 Thursday, April 15, 2004 3:30 PM

Advertising