JVC LPT0976-001B - Manual (Page 54)

Filename [MX1SEU_10Timer Recording.fm]
Masterpage:Left0
54
EN
Page 54Monday, 6 December 2004 14:01
TIMER RECORDING ON VHS DECK
You can programme this unit to timer-record as many as 8
programmes.
With the
a
system, timer programming is greatly simplified
because each TV programme has a corresponding code number
which your unit is able to recognise.
You can use the remote control to enter the
a
number.
1
Load a cassette with the record safety tab intact.
2
Press VHS so that the VHS lamp lights up on the unit.
3
Press PROGRAMME to access
the Programme screen.
4
Press F G to select
ASHOWVIEW PRGMB, then
press ENTER.
5
Press the number keys to enter
the
a
number of a
programme you wish to record,
then press ENTER.
● If you have made a mistake,
press CANCEL and input the
correct number before you press
ENTER.
● If the number you entered is
invalid,
AERRORB appears on the TV screen and AErrB appears
on the front display panel.
Press CANCEL and input a valid
a
number.
6
The
a
number you
entered and the matching timer-
recording information are
displayed on the TV screen.
Check the programme data.
● To cancel this setting, press
PROGRAMME.
7
Press REC MODE to select the desired recording mode. Or
press
D E to select ASP/LPB, then press F G to select the
desired recording mode.
8
Press D E to select AVPS/PDCB, then press F G to select the
desired channel.
9
Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 9.
● If APROGRAM OVERLAPPEDB appears on the TV screen, see
page 56.
10
Press VHS j to engage the unit’s timer mode. The VHS
recording lamp lights up on the unit and the HDD or DVD deck
is automatically selected. Press
A to turn off the unit. When
the HDD or DVD deck is in timer standby mode, the unit is
automatically turned off.
● The VHS timer indicator lights up on the front display panel
when the VHS deck is set to the timer recording standby
mode by pressing VHS
j. However, it will blink rapidly when
VHS j is pressed under the following conditions:
● Clock is not set.
● Timer programming has not been set.
● Cassette is not loaded.
● Timer recording standby mode with a cassette without record safety
tab inserted
● To disengage the timer mode, press VHS j again.
NOTES:
● To Timer-Record Weekly Or Daily Serials:
^ in step 6, press number keys A9B for weekly serials or
number keys
A8B for daily serials (Monday - Friday). Either
AWEEKLYB or ADAILYB appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
● You can programme this unit to timer-record as many as 8
programmes. If you try to programme the unit to record a ninth,
APROGRAM FULLB appears on the TV screen and AFULLB
appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary programmes.
(A pg. 56)
● To record the programmes received by satellite receiver, record
on the HDD or the DVD discs. For details, refer to
Ac Timer
Programming B (A pg. 49)
b
Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
0-9
REC MODE
VHS#
VHS
CANCEL
PROGRAMME
rtwe
ENTER
CABLE/SAT
DVD TV
PROGRAMME
[ JK] N [ENTER]
[PROGRAMME] : EXIT
NSHOWVIEW PRGM
PROGRAMME/CONFIRM
[0-9] N [ENTER]
[ L] : DELETE
[PROGRAMME] : EXIT
SHOWVIEW SYSTEM
CURSOR : [ HI] SELECT : [JK]
CONFIRM : [ENTER]
DATE START
DAILY/WEEKLY TV PROG
STOP
SP/LP
SP
ARD
VPS/PDC
OFF
MON-FRI
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see
Ac System SetupB (A pg. 83) and
set the Guide Programme number correctly.
IMPORTANT:
If you have moved to a different area or if a broadcasting
station’s programme number has been changed, the wrong
programme number will be displayed on the
a
programme screen in step 6. When this happens, set the correct
Guide Programme number for that station. (A pg. 83,
Ac
System Setup B)
MX1SEU_00.book Page 54 Monday, December 6, 2004 2:01 PM