JVC LPT0976-001B - Manual (Page 81)

Masterpage:Right+
EN
81
Filename [MX1SEU_13Subsidiary.fm]
SUBSIDIARY SETTINGS
Page 81Monday, 6 December 2004 14:01
You can change various mode settings on the Function Set
screen.
To change the settings of these modes, find the desired mode in
the menu (for details on each menu, see pages 81 through 82),
then follow the procedure below.
1
Press VHS so that the VHS lamp lights up on the unit.
2
Press SET UP to access the
Function Set screen.
3
Press F G to select the item you
want to change, then press
ENTER or
E to select the desired
mode.
4
Press SET UP to complete the
setting.
* The boldface settings below indicate the settings at your purchase.
8
B.E.S.T. ^ ON / OFF
You can set the B.E.S.T. (Biconditional Equalised Signal Tracking)
system to
AONB or AOFFB. (A pg. 45)
NOTES:
● When watching a tape recorded with AB.E.S.T.B set to AONB, it is
recommended that you leave B.E.S.T. on during playback as
well.
● When watching a rental tape or one recorded on another video
recorder, or when using this unit as the player for editing, set
B.E.S.T. to your preference.
● The B.E.S.T. system works for both SP and LP modes only after
a tape has been inserted and the Record mode is first initiated. It
does not work during recording.
● The B.E.S.T. system does not work while Automatic Satellite
Programme Recording is in progress. (A pg. 45)
● In the case of timer recordings, the B.E.S.T. system works before
recording is initiated.
● Once the cassette is ejected, the B.E.S.T. data is cancelled. The
next time the cassette is used for recording, B.E.S.T. is re-
performed.
● Pressing the unit’s R button while ABESTB is displayed does not
start Instant Timer Recording. (A pg. 45)
8
PICTURE CONTROL ^ AUTO / EDIT / SOFT
This feature helps you to adjust the playback picture quality
according to your preference. Normally select
AAUTOB .
AUTO :
Picture quality is adjusted automatically.
EDIT:
Minimises picture degradation during editing (recording and
playback).
SOFT:
Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
NOTES:
● When you select AEDITB or ASOFTB, the selected mode will not
change until you select another mode.
● When you select AEDITB to dub tapes, be sure to select ANORMB
after you finish dubbing the tapes.
● When AB.E.S.T.B is AOFFB, APICTURE CONTROLB switches
automatically from AAUTOB to ANORMB.
8
O.S.D. ^ AUTO / OFF
When this function is set to AAUTOB, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (A pg. 20)
NOTES:
● Even when AO.S.D.B is set to AOFFB, you can display the various
operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to
set
AO.S.D.B to AOFFB before starting.
● During playback, the operation mode indicators may be disturbed
depending on the type of tape being used.
Mode Set
(VHS Deck Only)
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
rtwe
SET UP
ENTER
VHS
CABLE/SAT
DVD TV
ON
AUTO
AUTO
OFF
PAL/NTSC
B.E.S.T.
PICTURE CONTROL
O.S.D.
AUTO SP
NLP TIMER
COLOUR SYSTEM
MODE SET
[ JK] N [ENTER]
[SET UP] : EXIT
MX1SEU_00.book Page 81 Monday, December 6, 2004 2:01 PM