Samsung MINI SMART SCC-C7325 - Manual (Page 21)

English – 21
ENG
Operation
CHECK POINTS BEFORE OPERATION
Before power is applied, please check the cables carefully.
The camera ID of the controller must be identical to that
of the camera to be controlled. The camera ID can be
checked in the System Information of OSD Menu.
If your controller supports multi-protocols, the protocol
must be changed to match to that of the camera.
If you changed camera protocol by changing DIP switch,
the change will be effective after you reboot the camera.
Since the operation method can be different for
each controller available, refer to the manual for your
controller if camera can not be controlled properly.
PRESET AND PATTERN
FUNCTION PRE-CHECK
Check how to operate Preset, Scan, Auto Pan and
Pattern function with controller or DVR in advance to
operate camera function using them. (refer to your
System keyboard Manual)
If controller or DVR has no pattern button or function,
use shortcut keys with preset numbers. For more
information, refer to “Reserved Preset” in this manual.
AUTO CALIBRATION
If the camera is continuously subjected to very high
temperature (over 50°C or 122°F) environment for a
long time, it is possible for the camera to lose focus.
As a result, you will get blurry image. In this case, it is
recommended to turn on “AUTO CALIBRATION” by
running Preset 165.
If you execute AUTO CALIBRATION, camera will
calibrate its focus at every 6 hours. To turn off this
function, please, Run Preset 166.
STARTING OSD MENU
Function
Using the OSD menu, Preset, Pattern, Auto Pan,
Scan and Alarm Input function can be confi gured for
each application.
Enter Menu
<Go Preset> [95]
RESERVED PRESET
Description
Some Preset numbers are reserved for direct access
to specifi c functions in OSD menu. These direct
commands via preset provide quick execution of
•
•
•
•
•
•
•
•
•
•
•
•
various functions using keyboard controller as well as
simplify the interface with DVR and IP equipments.
Function
<Go Preset> [95] : Enters into OSD menu
<Go Preset> [131~134] : Runs Pattern Function 1 ~ 4
<Go Preset> [141~148] : Runs Auto Pan Function 1 ~ 8
<Go Preset> [151~158] : Runs Scan Function 1 ~ 8
<Go Preset> [161] : Sets Relay Output to OFF
<Set Preset> [161] : Sets Relay Output to ON
<Go Preset> [165] : Auto Calibration ON
<Go Preset> [166] : Auto Calibration OFF
<Go Preset> [167] : Zoom Proportional Jog ON
<Set Preset>[167] : Zoom Proportional Jog OFF
<Go Preset> [170] : Sets Camera BLC Mode to OFF
<Go Preset> [171] : Sets Camera BLC Mode to HIGH
<Go Preset> [174] : Sets Camera Focus Mode to
AUTO
<Go Preset> [175] : Sets Camera Focus Mode to
Manual
<Go Preset> [176] : Sets Camera Focus Mode to
SEMI-AUTO
<Go Preset> [177] : Sets Day & Night Mode to
AUTO1
<Go Preset> [178] : Sets Day & Night Mode to
NIGHT
<Go Preset> [179] : Sets Day & Night Mode to DAY
<Go Preset> [190] : Sets OSD Display Mode to
AUTO (Except Privacy Mask)
<Go Preset> [191] : Sets OSD Display Mode to OFF
(Except Privacy Mask)
<Go Preset> [192] : Setting OSD Display Mode to
ON (Except Privacy Mask)
<Go Preset> [193] : Sets all Privacy Mask Display to
OFF
<Go Preset> [194] : Sets all Privacy Mask Display to
ON
<Go Preset> [195] : Heater ON (Turn off after 5mins
and switch to Auto mode)
<Go Preset> [196] : Heater OFF (Turn off and switch
to Manual mode)
<Go Preset> [197] : Fan ON (Turn off after 5mins
and switch to Auto mode)
<Go Preset> [198] : Fan OFF (Turn off and switch to
Manual mode)
<Go Preset>[200] : Digital Zoom ON
<Go Preset>[201] : Digital Zoom OFF
•