Other things to know, 4a. dimensions/specifications fig. 12 – Kenmore 625.348670 User Manual
Page 20
OTHER THINGS TO KNOW
SECTION 4
20
4A.
DIMENSIONS/SPECIFICATIONS
FIG. 12
BYPASS VALVES
Bypass
Valve
Inlet
Valve
Outlet
Valve
3 -- VALVE
FOR SERVICE
close bypass valve
open inlet & outlet valves
FOR BYPASS
open bypass valve
close inlet & outlet valves
PUSH IN
for bypass
PULL OUT
for service
SINGLE
Bypass valve(s) should always remain in soft
water service position. Position in “bypass”
only if needed for softener repairs.
A
B
C
D
E
F
INCHES
CM
A
Salt Tank Height
40-1/4
102.2
B
Resin Tank Diameter (nominal)
9
22.7
C Resin Tank Height (nominal)
40
101.6
D Inlet-Outlet Height
41-1/2
105.4
E
Overall Height
47
119.4
F
1
Length
19-1/2
49.5
F
2
Width
16-1/2
41.9
—
Distance between inlet-outlet
center lines
3-7/8
9.8
MODEL NO. 625.348670
TIMER HF CODE HF32
NOTE: Please see the rating decal for water softener operating capacity, salt usage and service flow rate/pres-
sure loss performance specifications. Performance specifications are validated by the Water Quality Associa-
tion (WQA). The rating decal is located on the rim, under the salt hole cover (see page 30).
WATER SUPPLY TO WATER SOFTENER
MINIMUM WATER SYSTEM FLOW (gpm)
3
. . . . . . . . . . . . . . . .
MINIMUM-MAXIMUM WATER PRESSURE (psi)
20-120
. . . . . .
MAXIMUM WATER TEMPERATURE (°F)
120
. . . . . . . . . . . . . . .
MAXIMUM WATER HARDNESS (gpg)
110
. . . . . . . . . . . . . . . . . .
MAXMUM “CLEAR WATER”IRON (ppm)
8
. . . . . . . . . . . . . . . . .
SALT FOR WATER SOFTENER
TYPE OF SALT NEEDED
Nugget/Pellet
. . . . . . . . . . . . . . . . . . . .
ALTERNATE TYPE OF SALT
Pure, evaporated, compacted
. .
water softener salt
STORAGE CAPACITY (pounds)
200
. . . . . . . . . . . . . . . . . . . . . . .
OTHERS
TYPE OF ION EXCHANGE MATERIAL (resin)
High Capacity
AMOUNT OF RESIN (cu.ft.)
1.05
. . . . . . . . . . . . . . . . . . . . . . . . . .
REGENERATION (RECHARGE) CYCLE TIME (min.)
FILL (NaCL setting)
2.7-10.6
. . . . . . . . . . . . . . . . . . . . . . . . . . .
FILL (KCl setting)
3.8-12.6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRINING / BR. RINSE
120-135
. . . . . . . . . . . . . . . . . . . . . . . . .
BACKWASH
7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAST RINSE
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOTAL REGENERATION TIME
139.4---164.4
. . . . . . . . . . . .
gpm = gallons per minute
psi = pounds per square inch
gpg = grains per gallon
ppm = parts per million