Linn AV Loudspeaker - Manual (Page 6)

R e p l a c i n g t h e f u s e
Should the mains fuse blow replace it only with an equivalent part. The fuse holder
is located just below the mains inlet socket. To replace the fuse disconnect the
product from the mains supply. Using a flat blade screwdriver remove and replace
the fuse. If the fuse blows a second time there is a fault in the product. Contact your
local retailer.
M a i n s v o l t a g e o p e r a t i n g r a n g e
AV 5150 Active Isobarik Bass Speaker
115V, 230V +/- 10%, 50-60Hz.
Setting the mains operating voltage
All products with a voltage selector switch must be set to the local mains supply
voltage before connecting to the mains supply.
Please check the setting of the voltage selector switch at the mains input socket
before connecting the product to a mains supply.
To set the mains operating voltage unplug the mains supply cable and using a flat
blade screwdriver turn the selector switch to the appropriate voltage.
Warning!! The power supply may be destroyed if it is connected to 240V when
set for 120V.
Power consumption
Product Operate mode Standby mode
AV 5150 Active Isobarik 25W-850W 5W
Bass Loudspeaker
S w i t c h i n g t h e p ro d u c t o n a n d o f f – s t a n d b y
o p e r a t i o n
AV 5150 Active Isobarik Bass Speaker
The AV 5150 contains circuitry which senses the presence of an audio signal and
powers up the product. The AV 5150 remains powered up for several minutes after
the audio signal disappears, then reverts to standby mode, consuming very little
power. Standby mode is indicated by the front panel indicator glowing red. Full
operation is indicated by the front panel indicator glowing green. The mains switch
(behind the control area cover) switches the product OFF completely or ON. If, after
three minutes, the AV 5150 does not sense an audio signal it will switch to standby
mode.
P o s i t i o n i n g t h e p r o d u c t s a n d h e a t
All electronic products generate some heat. Audio products, in particular audio
power amplifiers, have to handle and dissipate large amounts of power. It is
essential to provide adequate ventilation to allow this heat to dissipate into the
environment. All Linn products are fully protected against overheating and will shut
down before any component becomes over heated. However the products will last
longer and perform better if they are kept cool. The AV 5150 Active Isobarik Bass
Speaker keeps its power amplifier semiconductors cool by transferring the heat on
to the extruded heatsink. As a result the extrusion will become warm in use.
C o p y r i g h t a n d a c k n o w l e d g e m e n t s
Copyright © Linn Products Limited.
Linn Products Limited, Floors Road, Waterfoot, Glasgow, G76 0EP, Scotland, United
Kingdom.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written
permission of the publisher.
Printed in the United Kingdom.
AV 5101, AV 5103, AV 5105, AV 5110, AV 5120, AV 5140, and AV 5150 are
trademarks of Linn Products Limited.
The information in this manual is furnished for informational use only, is subject to
change without notice, and should not be construed as a commitment by Linn
Products Limited. Linn Products Limited assumes no responsibility or liability for any
errors or inaccuracies that may appear in this manual.
Part no: PACK 739
This manual was produced by Human-Computer Interface Ltd, Cambridge,
England.
pr
ef
ace
iv