Lincoln Electric POWER MIG SVM165-A - Manual (Page 28)

C-2 C-2 ACCESSORIES
POWER MIG 350MP
DRIVE ROLL KITS
Refer to Table C.1 for various drive roll kits that are
available for the Power MIG. All items in Bold are
supplied standard with the Power MIG.
TABLE C.1
* .035 Aluminum recommended for Push-Pull systems only.
3/64" (1.2 mm) ALUMINUM
FEEDING KIT (K2153-1)
This kit helps push feeding aluminum through stan-
dard machine feeder and gun. It provides gun and
wire drive conversion parts to weld with 3/64" (1.2
mm) aluminum wire. 5356 alloy aluminum wire is rec-
ommended for best push feeding performance.
Kit includes drive rolls and wire guide plate for the
wire drive, liner and two contact tips for the gun, along
with installation instructions.
K363P READI-REEL ADAPTER
The K363P Readi-Reel Adapter mounts to the 2"
spindle. It is needed to mount the 22-30 lb. Readi-
Reels.
DUAL CYLINDER MOUNTING KIT
(K1702-1)
Permits stable side-by-side mounting of two full size
(9" dia. x 5' high) gas cylinders with “no lift” loading.
Simple installation and easy instructions provided.
Includes upper and lower cylinder supports, wheel
axles and mounting hardware.
ALTERNATIVE MAGNUM GMAW
GUN AND CABLE ASSEMBLIES
The following Magnum 350MP gun and cable assem-
blies are separately available for use with the Power
MIG 350MP. Each is rated 300 amps 60% duty cycle
(or 300 amps 40% duty) and is equipped with the inte-
grated connector, twist-lock trigger connector, fixed
nozzle and insulator, and includes a liner, diffuser,
and contact tips for the wire sizes specified:
MAGNUM GUN CONNECTION KIT
(Optional K466-6)
Using the optional K466-6 Magnum Connection kit for
the Power MIG permits use of standard Magnum 200,
300 or 400 gun and cable assemblies.
K1692-2 SPOOL GUN (PRINCE TM XL)
When the Power MIG Gun Selector Switch is in the
“Standard / Spool Gun” position, the Power MIG provides
gun trigger switch transfer between the Magnum gun or
the spool gun for the same polarity welding with different
wire and gas processes.
Closing either gun trigger will cause the electrode of
both guns to be electrically “HOT”. Be sure unused
gun is positioned so electrode or tip will not contact
metal case or other metal common to work.
-----------------------------------------------------------------------
Because the control circuitry senses each gun through
its trigger leads, weld parameters are displayed and
adjustable for the last gun that was triggered.
1. Pulling the trigger for the built-in feeder gun
(Magnum 300):
•
Disables spool gun operation.
• Changes the displays of the Power MIG 350MP to
correspond to feeder gun operation.
• Closing feeder gun trigger starts feeder gun weld-
ing and makes both electrodes electrically “HOT”.
2. Pulling SPOOL GUN Trigger:
• Disables built-in feeder gun operation.
• Changes the displays of the Power MIG 350MP to
correspond to Spool Gun operation.
• Closing spool gun trigger starts spool gun welding
and makes both electrodes electrically “HOT”.
3. Operation with Power MIG 300:
• Install the spool gun per the installation instructions
• Turn the Power MIG 350MP input power ON.
• Make sure that the Gun Selector Switch is in the
“Standard / Spool Gun” position.
• Pull and release the trigger of the Spool Gun. The
Power Mig recognizes the spool gun as active and weld
parameters are adjustable for welding with the Spool
Gun
Non-Synergic Weld Modes (Mode 5)
Wire Size Drive Roll Kit
.023”-.030” (0.6-0.8 mm) KP1696-030S
Solid
.035” (0.9 mm) KP1696-035S
Steel
.045” (1.2 mm) KP1696-045S
.040” (1.0mm) KP-1696-2
.035-.045” (0.9-0.2mm) KP-1696-1
Cored
.035” (0.9 mm) KP1697-035C
.045” (1.2 mm) KP1697-045C
Aluminum 3/64” (1.2 mm) KP1695-3/64A
English Wire Metric Wire
Length Part No. Size Size
10' (3.0 m) K470-1
12' (3.6 m) K470-7 .035 – .045" 0.9 – 1.2 mm
15' (4.5 m) K470-3
CAUTION
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC