Panasonic AJ-HDX900E - Manual (Page 109)

109
7
Chapter 7 Menu description tables
(continued)
The underlining in the variable range column indicates the setting in the preset
mode.
Item
Variable
range
Remarks
B (PHASE) –63
:
+00
:
+63
For performing the hue correction for blue.
B-Cy (PHASE) –63
:
+00
:
+63
For performing the hue correction between
blue and cyan.
Cy (PHASE) –63
:
+00
:
+63
For performing the hue correction for cyan.
Cy-G (PHASE) –63
:
+00
:
+63
For performing the hue correction between
cyan and green.
G (PHASE) –63
:
+00
:
+63
For performing the hue correction for green.
G-Yl (PHASE) –63
:
+00
:
+63
For performing the hue correction between
green and yellow.
Yl (PHASE) –63
:
+00
:
+63
For performing the hue correction for yellow.
Yl-R (PHASE) –63
:
+00
:
+63
For performing the hue correction between
yellow and red.
Mg (PHASE) –63
:
+00
:
+63
For performing the hue correction for
magenta.
R (PHASE) –63
:
+00
:
+63
For performing the hue correction for red.
R-Mg (PHASE) –63
:
+00
:
+63
For performing the hue correction between
red and magenta.
Mg-B (PHASE) –63
:
+00
:
+63
For performing the hue correction between
magenta and blue.
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
∫ MATRIX TABLE OFF
A
B For selecting the color correction table for
the linear matrix.
∫ COLOR
CORRECT
ON
OFF For switching ON/OFF of the 12-axis
independent color correction.
7-3-5 LOW SETTING
Item
Variable
range
Remarks
∫ MASTER GAIN –3dB
:
0dB
:
30dB
For setting the master gain to –3, 0, 3, 6, 9,
12, 15, 18, 21, 24, 27 or 30 dB.
H.DTL LEVEL 00
:
10
:
63
For performing the horizontal detail
correction level setting.
V.DTL LEVEL 00
:
20
:
31
For performing the vertical detail correction
level setting.
DTL CORING 00
:
01
:
15
For performing the noise elimination level
setting for detail.
H.DTL FREQ. 00
:
18
:
31
For performing the horizontal detail
frequency selection.
Approximate peak frequencies
0: 9 MHz 10: 10 MHz
20: 12 MHz 30: 15 MHz
LEVEL DEPEND. 0
1
:
5
For setting the LEVEL DEPEND.
When the Y-detail is emphasized, details of
dark sections are compressed.
If the numerical value is larger, details of
bright sections are also compressed.
MASTER GAMMA 0.30
:
0.45
:
0.75
For setting the master gamma.
(0.01 step)
BLACK GAMMA –3
:
OFF
:
+3
For setting the gamma curve for the dark
portion.
–3 to –1:
The dark portion is compressed.
OFF:
Standard state
+1 to +3:
The dark portion is extended.
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S C U F R
S U F R
∫ COLOR
CORRECT
ON
OFF For switching ON/OFF of the 12-axis
independent color correction of the position
selected with the GAIN switch (L, M, H).
S C U F R
<Notes>
O If the master gain is set to –3dB for shooting, coloring
phenomenon may occur in the high brightness portion of
the images.
To reduce this phenomenon, reduce the KNEE SLOPE
value on the KNEE/LEVEL screen, then check that the
coloring phenomenon does not occur and shoot again.
To activate the KNEE SLOPE value, perform the following
settings.
OUTPUT/AUTO KNEE selector switch
CAM. AUTO KNEE OFF
∫ MANUAL KNEE item on the KNEE/LEVEL screen
ON
O Items with $ in front of their names are set by the PAINT
MENU SW ($) R/W menu items on the <CARD R/W
SELECT> screen.
Items without $ in front of their names are set by the
PAINT MENU LEVEL R/W menu item.
For details, refer to “7-6-2 CARD R/W SELECT.”