Pioneer VSX-LX70 - Manual (Page 28)

Controls and displays 04
28
En
7 TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CTRL button. Thus if you only have one TV to hook
up to this system assign it to the TV CTRL input source
button. If you have two TVs, assign the main TV to the TV
CTRL button (see page 74 for more on this).
TV – Use to turn on/off the power of the TV.
TV VOL +/– – Use to adjust the volume on your TV.
INPUT SELECT – Use to select the TV input signal.
TV CH +/– – Use to select channels.
8 Component control buttons
The main buttons ( , , etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD , DVR1 or TV ). The following controls
can be accessed when listening to the built-in tuner:
MPX – Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 35).
DISP – Switches between named station presets and
radio frequencies (page 36).
9 STATUS
Press to check selected receiver settings (page 72).
10 MULTI OPE
Use this button to perform multi operations (page 76).
11 SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT ), or to display the currently
selected input source in the remote control LCD.
12 SOURCE
Press to turn on/off other components connected to the
receiver (see page 74 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system on page 74):
SETUP – Indicates the setup mode, from which you
choose the options below.
PRESET – See Selecting preset codes directly on
page 74.
LEARNING – See Programming signals from other
remote controls on page 74.
MULTI OP – See Multi Operation and System Off on
page 76.
SYS OFF – See Multi Operation and System Off on
page 76.
DIRECT F – See Direct function on page 76.
RENAME – See Renaming input source names on
page 76.
ERASE – See Erasing one of the remote control button
settings on page 75.
RESET – See Resetting the remote control presets on
page 75.
READ ID – See Confirming preset codes on page 75.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
ANALOG ATT , etc.)). Also use this button to set up
surround sound (page 8, page 37). With SHIFT , this
selects the MULTI-ZONE control (page 56), shown in the
display as
RCV/Z2 , RCV/Z3 .
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 Receiver controls
SIGNAL SEL – Use to select an input signal (page 32).
SBch – Use to select the surround/virtual back
channel mode (page 32).
STEREO/F.S.SURR – Switches between the stereo
playback mode (page 31) and the Front Stage
Surround Advance mode (page 31).
THX – Press to select a Home THX listening mode
(page 30).
STANDARD – Press for Standard decoding and to
switch between the various 2 Pro Logic IIx and
Neo:6 options (page 29).
ADV.SURR – Use to switch between the various
surround modes
(page 30).
18 PHASE – Press to switch on/off Phase Control or Full
Band Phase Control (page 10).
MCACC – Press to switch between MCACC presets
(page 32).
S.DIRECT – Press to select Auto Surround (page 29)
or Stream Direct (page 31) listening.
VSX_LX60LX70.book 28 ページ ２００７年７月１８日 水曜日 午前１０時１９分