Pioneer VSX-LX70 - Manual (Page 77)

Controlling the rest of your system 12
77
En
5 Use / to select a command in the sequence then
press ENTER .
If this is the first command in the sequence, select 1ST
CODE . Otherwise, simply choose the next command in
the sequence. PRES KEY flashes after you press ENTER .
6 If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
7 Select the button for the command you want to
input.
The following remote control commands can be selected:
• You don’t need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components , you don’t need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
• program the power to switch on if it’s the source
component selected in step 3;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
8 Repeat steps 5–7 to program a sequence of up to
five commands.
9 When you’re finished, use / to select EDITEXIT
from the menu and press ENTER .
You will return to the remote control SETUP menu. Select
* EXIT * again to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press SOURCE .
The command sequence you programmed will run, then
all Pioneer components will switch off 1 , followed by this
receiver.
Controls for TVs
This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see
Setting the remote to control other
components on page 74 for more on this). Use the input
source buttons to select the component.
SLEEP
CLEAR
+10
SR+
ANALOG
ATT
DISC
DIMMER
CLASS D.ACCESS
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TV CONTROL
DVD TV BD TV CTRL
DVR1
TUNE
TUNE
ST ST
i Pod TUNER RECEIVER
ENTER
A PARAMETER
TOP MENU ì
V PARAMETER
MENU T.EDIT
BAND
RETURN SETUP
PROGRAM
CD
DVR2 HOME MEDIA GALLERY
CD-R
ZONE2/3
ì
CH
LEVEL
GENRE
ì
HDMI
TV CONTROL
VOL
STATUS SIGNAL SEL
T.DISP
SBch STEREO/
F.S.SURR
JUKEBOX
TV CH INPUT
SELECT
MPX
AUDIO SUBTITLE
INFO
MUTE
REC
TV VOL
REC STOP
HDD
CH CH
DVD
PROGRAM
DISP
PHOTO
TV/DTV
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
SHIFT
STATUS STATUS
MCACC S.DIRECT
MULTI OPE
SIGNAL SEL
T.DISP
SBch
STEREO/
F.S.SURR
ADV. SURR STANDARD
PHASE
THX
RECEIVER
PHOTO
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
DVD TV BD TV CTRL
CD
HOME MEDIA
CD-R HDMI
SHIFT
STATUS STATUS
MCACC S.DIRECT
MULTI OPE
SIGNAL SEL
T.DISP
SBch STEREO/ F.S.SURR
ADV. SURR STANDARD
PHASE
THX
RECEIVER
PHOTO
VSX_LX60LX70.book 77 ページ ２００７年７月１８日 水曜日 午前１０時１９分