Pioneer VSX-LX50 - Manual (Page 26)

Controls and displays 04
26
En
7 TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CTRL button. Thus if you only have one TV to hook
up to this system assign it to the TV CTRL input source
button. If you have two TVs, assign the main TV to the TV
CTRL button (see page 62 for more on this).
TV – Use to turn on/off the power of the TV.
TV VOL +/– – Use to adjust the volume on your TV.
INPUT SELECT – Use to select the TV input signal.
TV CH +/– – Use to select channels.
8 Component control buttons
The main buttons ( , , etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD , DVR1 or TV ). The following controls
can be accessed when listening to the built-in tuner:
MPX – Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 35).
DISP – Switches between named station presets and
radio frequencies (page 36).
9 STATUS
Press to check selected receiver settings (page 60).
10 MULTI OPE
Use this button to perform multi operations (page 64).
11 SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT ), or to display the currently
selected input source in the remote control LCD.
12 SOURCE
Press to turn on/off other components connected to the
receiver (see page 62 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system on page 62):
SETUP – Indicates the setup mode, from which you
choose the options below.
PRESET – See Selecting preset codes directly on
page 62.
LEARNING – See Programming signals from other
remote controls on page 62.
MULTI OP – See Multi Operation and System Off on
page 64.
SYS OFF – See Multi Operation and System Off on
page 64.
DIRECT F – See Direct function on page 64.
RENAME – See Renaming input source names on
page 64.
ERASE – See Erasing one of the remote control button
settings on page 63.
RESET – See Resetting the remote control presets on
page 63.
READ ID – See Confirming preset codes on page 63.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
ANALOG ATT , etc.)). Also use this button to set up
surround sound (page 8, page 37).
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 Receiver controls
SIGNAL SEL – Use to select an input signal (page 30).
SB ch – Use to select the surround/virtual back
channel mode (page 30).
STEREO/F.S.SURR – Switches between the stereo
playback mode (page 29) and the Front Stage
Surround Advance mode (page 29).
THX – Press to select a Home THX listening mode
(page 28).
STANDARD – Press for Standard decoding and to
switch between the various 2 Pro Logic IIx and
Neo:6 options (page 27).
ADV.SURR – Use to switch between the various
surround modes (page 28).
18 PHASE – Press to switch on/off Phase Control
(page 10).
MCACC – Press to switch between MCACC presets
(page 30).
S.DIRECT – Press to select the Auto Surround mode
(page 27) or the Stream Direct mode (page 29).
Stream Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 29).
VSX-LX50.book 26 ページ ２００７年４月１２日 木曜日 午後５時３分