Pioneer VSX-LX50 - Manual (Page 63)

Controlling the rest of your system 12
63
En
• The remote controls should be 3 cm to 5 cm apart.
5 Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver’s remote control.
For example, if you want to learn the playback control
signal, press and hold
briefly. The LCD display will
show OK if the operation has been learned.
1
If for some reasons the operation hasn’t been learned the
LCD will display
ERROR briefly and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows OK . 2
Certain buttons represent operations that cannot be
learned from other remote controls.
3
The buttons
available are shown below (with the exception of the TV
controls, a combination of
SHIFT and these buttons can
also be learned):
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold the RECEIVER button for a couple of
seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP .
2 Use / to select ERASE then press ENTER .
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
3 Press the input source button corresponding to the
command to be erased then press ENTER .
The LCD display flashes PRES KEY .
4 Press and hold the button to be erased for two
seconds.
The LCD display shows OK or NO CODE to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for a couple of
seconds when you’re done.
Resetting the remote control presets
This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP .
2 Use / to select RESET then press ENTER .
RESET flashes in the LCD display.
3 Press and hold ENTER for about two seconds .
The LCD shows OK to confirm the remote presets have
been erased.
Confirming preset codes
Use this feature to check which preset code is assigned
to an input source button.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP .
2 Use / to select READ ID then press ENTER .
The LCD on the remote prompts you for the input source
button you want to check.
Note
1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
2 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows FULL , it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button
you’re not using to free up more memory (note that some signals may take more memory than others).
3 Note that the number key decimal button (
+10 / D.ACCESS ) may not be learned with some components.
3 cm to 5 cm
ANAL O G AT T MIDNIGHT/ L OUDNESS
DIMMER
SLEEP SR+ +10
D. A CCESS DIAL OG E
S.RETRIEVER
CL ASS DISC
RECEIVER
SOURCE SY STEM OFF
INPUT SELECT ENTER TV C O NTROL
SHIFT
V OL
TUNE TUNE ST
ST
ST AT US SIGNAL SEL THX
AD V. SURR
SB ch
INPUT SELECT
TV CH
MPX A B
CD
E
EON
AU D IO DISP SUB TITLE
MUL TI OPE
ST ANDARD
PHASE
S.DIRECT
MC AC C
REC
MUTE
TV V OL
ENTER
REC ST OP JUKEBO X
HDD CH
CH D VD
TOP MENU AV P A R A M ETER
C H LEVEL
PT Y SEARCH
T. ED IT MENU RETURN
GUIDE
BAND
SETUP
RECEIVER TV
D V R 1 TV CTRL
iP od
RECEIVER
TUNER
HDMI 1
D VD
CD
HDMI 2
CD-R/T A PE
DV R 2
USB
STEREO/ F.S.SURR
PHO TO
ANALOG
ATT
MIDNIGHT/
LOUDNESS
DIMMER
SLEEP
SR+
+10 D.ACCESS
DIALOG E
S.RETRIEVER
CLASS DISC
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TUNE
TUNE
ST ST
ENTER
TOP MENU
AV PARAMETER CH LEVEL
PTY SEARCH
T.EDIT
MENU
RETURN
GUIDE BAND
SETUP
TV DVR 1 TV CTRL
iPod RECEIVER TUNER HDMI 1
DVD
CD HDMI 2 CD-R/TAPE
DVR 2 USB
RECEIVER
TV CONTROL
SHIFT
VOL
STATUS SIGNAL SEL
THX ADV.SURR
SB ch
INPUT
SELECT TV CH
MPX
A
B C D E
EON
AUDIO
DISP
SUBTITLE
MULTI OPE STANDARD
PHASE S.DIRECT MCACC
REC
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH CH
DVD
STEREO/
F.S.SURR
PHOTO
VSX-LX50.book 63 ページ ２００７年４月１２日 木曜日 午後５時３分