Pioneer VSX-LX50 - Manual (Page 71)

Additional information 13
71
En
Display
After using the Auto MCACC
Setup, the speaker size setting is
incorrect. • There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch
off all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.
You can change the speaker setting manually in
Speaker Setting on page 46, and use the ALL (Keep
SPsetting) option for the Auto Mode in Automatic MCACC (Expert) on page 37 if this is a recurring
problem.
Can’t adjust the Fine Speaker
Distance setting (page 41)
properly. • Check that the speakers are all in phase (make sure the positive ( + ) and negative ( – ) terminals are
matched up properly).
Most recent settings have been
erased. • The power cord was disconnected from the wall while adjusting this setting.
Symptom Remedy
Symptom Remedy
The display is dark or off. • Press DIMMER on the remote control repeatedly to select a different brightness.
After making an adjustment the
display goes off. • Press DIMMER on the remote control repeatedly to select a different brightness.
You can’t get DIGITAL to display
when using the SIGNAL SELECT
button.
• Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input
Setup menu on page 56).
• If the multichannel analog inputs are selected, select a different input source.
The Dolby/DTS indicator doesn’t
light when playing Dolby/DTS
software. • These indicators do dot light if playback is paused.
• Check the playback (especially the digital output) settings of the source component.
When playing a DVD-Audio disc,
the DVD player display shows
96 kHz . However, the receiver’s
display does not.
• This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog outputs of
the DVD player. This receiver cannot show the playback sample rate when using the analog inputs.
During playback of a DTS 96/24
source, the display doesn’t show
96 kHz .
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 30).
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light. • Check that the player is connected using a digital connection.
• Make sure that the receiver is set to
AUTO or DIGITAL (see Choosing the input signal on page 30).
• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.
• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.
When playing certain discs, none
of the receiver’s format
indicators light. • The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what audio
tracks are recorded on the disc.
When playing a disc, the
2 PL II or Neo:6 indicator lights
on the receiver.
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 30).
• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is not a
malfunction. Check the disc packaging for details about the audio tracks available.
During playback of a Surround
EX or DTS-ES source on the
SBch
AUTO setting, the EX and ES
indicators don’t light, or the
signal is not properly processed.
• The source may be Dolby Surround EX/DTS-ES software, but it has no flag to indicate it is 6.1 compatible.
Set to
SBch ON (see Using surround back channel processing on page 30) then switch to the THX Surround
EX or Standard EX listening mode (see Listening in surround sound on page 27).
During playback of DVD-Audio,
the display shows
PCM .
• This will occur when playing DVD-Audio material over the HDMI connection. This is not a malfunction.
VSX-LX50.book 71 ページ ２００７年４月１２日 木曜日 午後５時３分