Pioneer VSX-LX50 - Manual (Page 70)

Additional information 13
70
En
Video
Settings
When playing a DTS format LD
there is audible noise on the
soundtrack. • Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 30).
Can’t record audio. • You can only make a digital recording from a digital source, and an analog recording from an analog
source.
• For digital sources, make sure that what you’re recording isn’t copy protected.
• Check that the
OUT jacks are properly connected to the recorders input jacks (see Connecting analog
audio sources on page 16).
Subwoofer output is very low. • To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see Speaker
Setting on page 46).
Everything seems to be set up
correctly, but the playback sound
is odd. • The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are
matched with the corresponding terminals on the speakers (see
Connecting the speakers on page 17).
The PHASE CONTROL feature
doesn’t seem to have an audible
effect.
• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to
the highest frequency setting. If there is a
PHASE setting on your subwoofer, set it to 0º (or depending on
the subwoofer, the setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker Distance on page 48).
Noise or hum can be heard even
when there is no sound being
input. • Check that personal computers or other digital components connected to the same power source are not
causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer. • See Automatically setting up for surround sound (Auto MCACC) on page 8 to set up your system again
using MCACC (this will automatically compensate for a delay in the subwoofer output).
The maximum volume available
(shown in the front panel display)
is lower than the
+12dB
maximum.
• This is not a malfunction. If the levels in Channel Level on page 47 have been adjusted, the maximum
volume will change accordingly.
Symptom Remedy
Symptom Remedy
No image is output when an input
is selected. • Check the video connections of the source component (see page 14).
• For high-definition video (using component video connections), or when digital video conversion is
switched off (in
Setting the AV options on page 58), you must connect your TV to this receiver using the same
type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component or HDMI cables
(see
The Input Setup menu on page 56).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
Can’t record video. • Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video cable is
used for connecting both the recorder and the video source (the one you want to record) to this receiver.
Noisy, intermittent, or distorted
picture. • Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-video or composite), then start playback again.
Symptom Remedy
The Auto MCACC Setup
continually shows an error. • The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also
Problems when using the Auto MCACC Setup on page 10). If the noise level cannot be kept low enough, you
will have to set up the surround sound manually (page 40).
VSX-LX50.book 70 ページ ２００７年４月１２日 木曜日 午後５時３分