Pioneer OPERATING INSTRUCTIONS DVR-920H - Manual (Page 108)

The Initial Setup menu 14
108
En
Set the date (day/month/year) and time, then
press ENTER to make all the settings.
Use the / (cursor up/down) buttons to change
the value in the highlighted field.
Use the
/
(cursor left/right) buttons to move
from one field to another.
Input Line System
• Default setting: 625System
For standard PAL or SECAM recording, leave the input
line system to
625System . When recording an NTSC or
PAL–60 signal through an external input, change to
525System .
1
On Screen Display
• Default setting: On
On the default setting, the recorder shows on-screen
operation displays (
Play, Stop and so on). Change to Off
to hide these displays.
Front Panel Display
• Default setting: On
On the default setting, the time is shown in the front
panel display when the recorder is in standby. Switch to
Off to have the front panel display switch off completely
when in standby.
2
Power Save
• Default setting: Off
When set to Off , signals arriving at the ANTENNA IN
terminal and at the AV2(INPUT 1/DECODER) AV
connector are passed through to the ANTENNA OUT
terminal and to the AV1(RGB)-TV AV connector,
respectively, when the recorder is in standby.
You can cut the standby power consumption of the
recorder by turning off the through function for one or
both terminals
3
:
• Mode1 – Through function only for the antenna
terminal
• Mode2 – No through function
• Off – Through function for both antenna terminal
and AV connector
Note
1 • When the current input is a built-in tuner channel preset, changing the input line system will usually also affect the input line system of the
AV2(INPUT 1/DECODER) input. However if the AV2/L1 In setting is set to Decoder (see AV2/L1 In on page 113), then the L2 input is affected
instead.
• If, when this setting is changed, the screen goes blank (due to incompatibility with your TV), you can switch back by pressing and holding
the front panel
button then pressing STOP REC (also front panel) while the recorder is stopped.
• When you switch the Input Line System setting the Copy List is erased.
• You can’t mix recordings of different TV line systems on the same disc.
• When you change this setting, the
Input Colour System setting also changes (see Input Colour System on page 111).
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator Clock Setting Manual Clock Setting 2 /2
Date
Time
Time Zone
Summer Time
01 01 2004 THU
00 00
England
London
On
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Mode
AV Link
Setup Navigator 525System
625System
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Mode
AV Link
Setup Navigator On
Off
Initial Setup
2 When set to Off , the display still lights dimly in standby when setting a timer recording.
3 When a timer recording is set with VPS/PDC on, SCART through is always active.
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Mode
AV Link
Setup Navigator On
Off
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Mode
AV Link
Setup Navigator Mode1
Mode2
Off
Initial Setup
DVR-04_HDD_UK.book 108 ページ ２００４年９月１０日 金曜日 午後７時３分