Roland HPD-15 - Manual (Page 40)

40
Chapter 2 Modifying a Patch
Adjusting the Multi-Effect Settings
Multi-effect (M-FX) allows you to select different algorithms
to obtain a variety of effects.
Parameter Category: MULTI-FX
fig.2-14
Type: Refer to MULTI-FX Type (p. 95)
Selects the preset setting of multi-effects.
If you wish to make even more detailed settings, adjust the
algorithm below and parameters on the following pages.
When you change a value, a “#” will appear beside the
“Type.”
Algo:
Selects the algorithm of the effect. The parameters and values
will differ depending on the algorithm.
Stereo EQ : Stereo Equalizer (Modify the tone)
CompLimiter : Compressor/Limiter (Make the volume
more consistent)
Enhancer : Enhancer (Add sparkle to the sound)
Spectrum : Spectrum (Add character to the sound)
Isolator : Isolator (Cut off a specific frequency range)
DynamicFltr : Dynamic Filter (Modify the tone according
to the volume)
Sustainer : Sustainer (Increase the duration of the sound)
Overdrive : Overdrive (Mildly distort the sound)
Distortion : Distortion (Severely distort the sound)
Lo-Fi : Lo-Fi (Simulate a “low-fidelity” sound)
RingModltr : Ring Modulator (Give the sound a metallic
character)
Stereo Cho : Stereo Chorus (Add depth and
spaciousness to the sound)
TetraChorus : Tetra Chorus (Layer chorus sounds to
create more spaciousness)
Tremolo Cho : Tremolo Chorus (Cyclically modulate the
volume to create spaciousness)
Space D : Space D (Add transparent spaciousness)
Stereo Fln : Stereo Flanger (Add metallic resonance to
the sound)
StepFlanger : Step Flanger (Add metallic resonance
while shifting the pitch by steps)
Phaser : Phaser (Give the sound a “swooshing”
character)
FbackPitch : Feedback Pitch Shifter (Shift the pitch)
StereoDelay : Stereo Delay (Delay the sound)
Mod Delay : Modulation Delay (Delay the sound while
modulating it)
TimeCtrlDly : Time Control Delay (Control the delay and
pitch in realtime)
3TapDlySht : 3-tap delay short (Delay the sound in three
directions)
3TapDlyLng : 3-tap delay Long
4TapDlySht : 4-tap delay short (Produce four delayed
sounds)
4TapDlyLng : 4-tap delay Long
AdvanceRev : Advanced Reverb (Add reverb to the sound)
GateReverb : Gate Reverb (Sharply cut the reverberation)
The parameters of each algorithm are explained on the
following pages.
In the explanation on the following pages, the value of
parameters marked with “RTM” can be controlled by [M-FX
DEPTH] of the Realtime Modify (p. 19).
* If you modify the MULTI-FX DEPTH in EZ Edit Mode (p.
25), the value of these parameters will be changed.
In the explanation on the following pages, the value of
parameters marked with “LFO” can be controlled by the
LFO. For details, refer to “Adding Cyclic Change to the
Tone” (p. 38).
In the explanation on the following pages, the value of
parameters marked by “Ctrl1, Ctrl2, Ctrl3” can be controlled by
the pads, D Beam, and ribbons. For details, refer to the section
on
CtrlTx: MFX Ctrl 1–3 in “Controlling the tone” (p. 52).
FxOut Volume:
Adjusts output volume of the multi-effects.
Fx Rev Send:
Adjusts the depth of reverb applied to the sound processed
by the multi-effects.
If you change the “Type,” the algorithm of the effect and the
values of the parameters will be changed to the setting of
each type.
U0101 MULTI-FX
Type# Hall"A"