Wolf Appliance Company SO30F/S - Manual (Page 23)

W O L F W A R M I N G D R A W E R S
23
P L A N N I N G I N F O R M A T I O N
The Wolf 30" (762) warming drawer is shipped
without any decorative drawer front. You must
order a L Series or E Series stainless steel
drawer front with handle, or the integrated front
(no handle) for a custom wood application.
Specifications on the following pages provide
overall dimensions, rough openings and installa-
tion options for Model WWD30 with L Series
and E Series stainless steel and integrated
drawer fronts. Note that there are significant
differences to the installation requirements for
the integrated drawer front.
An anti-tip block or platform must be used to
prevent the unit from tipping forward when the
drawer is opened.
The base platform must be able to support 200
lbs (91 kg). This platform must be a minimum of
1" (25) above the toe kick to allow for the 5 / 8 "
(16) overlap of the warming drawer trim.
Model WWD30 may be installed below a Wolf
built-in oven or an electric or gas cooktop,
provided the warming drawer is fully enclosed,
top and bottom. It may also be installed next to
or above another Model WWD30. Dimensions
will vary according to the specific installation.
S T A I N L E S S S T E E L D R A W E R F R O N T S
Wolf recommends using a 33" (838) wide
cabinet for the warming drawer with the L Series
and E Series stainless steel drawer front. A
minimum 30" (762) wide by 24" (610) deep
cabinet is required.
I N T E G R A T E D D R A W E R F R O N T
IMPORTANT NOTE: A minimum 33" (838) wide
cabinet is required for the warming drawer with
integrated drawer front. A minimum 24" (610)
deep cabinet is required for an overlay applica-
tion and 25" (635) deep cabinet for a flush inset
application.
Model WWD30 with integrated drawer front can
accommodate installations with a 30" (762) or
36" (914) cooktop. It may also be installed in
combination with a 30" (762) L Series or E Series
single or double oven or a 36" (914) L Series
single oven. Dimensions will vary according to
the specific installation.
Keep in mind that the width of the custom panel
for the warming drawer with integrated drawer
front will vary according to the specific installa-
tion. The opening width will remain 29 1 / 2 " (749)
whether installed in combination with a 30"
(762) or 36" (914) cooktop or oven.
The decorative wood drawer front panel must
be a minimum of 5 / 8 " (16) thick.
E L E C T R I C A L R E Q U I R E M E N T S
Model WWD30 requires a separate, grounded
120 V AC, 60 Hz power supply. The service
should have its own 15 or 20 amp circuit
breaker, and a grounded 3-prong receptacle
should be located within reach of the power
cord and flush with the back wall. Locate
electrical within the shaded area shown in the
installation illustrations on the following pages.
IMPORTANT NOTE: When installed outdoors, a
ground fault circuit interrupter (GFCI) is required
to reduce the risk of electrical shock.
F R O N T P A N E L O P T I O N S
Model WWD30
L Series Stainless Steel Drawer Front
Classic Finish WWDFRONT/S
Platinum Finish WWDFRONT/P
Carbon Finish WWDFRONT/B
E Series Stainless Steel Drawer Front
Framed – Classic WWDFRONT-2F/S
Unframed – Classic WWDFRONT-2U/S
Integrated Drawer Front
Accepts Wood Panel WWDFRONT/I
Optional drawer front panels are ordered
and shipped as a sales accessory.
Stainless steel drawer front panels include
handles to match L Series or E Series
built-in ovens.
A C C E S S O R I E S
Optional accessories
are available
through your Wolf
dealer. To obtain
local dealer
information, visit
the Showroom
Locator section of
our website,
wolfappliance.com.