Wayne-Dalton TORQUEMASTER 46 - Manual (Page 20)

20
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
20
IMPORTANT: RIGhT AND LEfT hAND
IS ALWAyS DETERMINED fROM INSIDE
ThE GARAGE LOOkING OuT.
Shake the TorqueMaster ® spring tube
assembly gently to extend the winding
shafts out about 5" on each side. for
single spring applications, there will be
no left hand spring in the
TorqueMaster
® spring tube assembly.
Lift the TorqueMaster ® spring tube
assembly and rest it on the top of the
flagangles.
NOTE: Cable drums are marked right
and left hand. Cable drums and
TorqueMaster
® spring tube assembly
are cam shaped to fit together only one
way.
Pre-wrap the TorqueMaster ® plus cable
drum with the counter balance cable
with 1/2 or 1-1/2 wraps (see
illustration)
To install the cable drum, slide the
correct cable drum over the winding
shaft until the cable drum seats against
the TorqueMaster
® spring tube
assembly.
The winding shaft must extend past the
cable drum far enough to expose the
splines and the groove. Align the
winding shaft groove with the round
notch in the flagangle.
For double spring applications:
Repeat for opposite side.
For single spring applications: Insert
the loose winding shaft into the left
hand cable drum prior to sliding the
cable drum over the TorqueMaster
®
spring tube assembly.
NOTE: On single spring applications,
take care in handling the loose winding
shaft (left side) so that it does not slide
back into the TorqueMaster
® spring
tube assembly.
Cable Drums
Tape Measure
WINDING
ShAfT
5”
TORquEMASTER ®
SPRING TuBE ASSEMBLy
Cable Drum
No space betw een R atchet Pawl a nd Cabl e Drum indicat es engagement
Cable Drum Ratch et Paw l
ENGAGE D SIDE VIEW
No space betw een Ratch et Pawl and Cable Drum
ENGAG ED UNDE RNE ATH VIEW
Space betw een Ratchet Paw
l
and Cable Drum non- indicates engage
men t
Cable Dru m
Ratch et Pawl
DIS ENG AGED SIDE VIEW
No spac e betwee n Ratch et Pawl and
DISE NGAGED UND ERNE ATH VIEW
UPPE R PO SITION
LOWE R PO SITION
LOWER POSI TION SIDE VIEW
UPPE R PO SITIO N SI DE VIE W
Ratc het Paw l in Lowe r Position
Ratch et Paw l in Up per Posit ion
Use th ese Ill ustrat ion, in conju nctio n with the I nstruc tions o n th e other sid e of
this lab el. WARNIN
G
Rach et Bra cket is
unde r
EXTR EME SP RING TENS ION.
To av oid p ossib le se vere or
fatal in
jury, D O NO
T re mov e
faste ners from ratch et bra cket
until sp
ring(s)
are fu lly
wnw ound.
To sa fely u nwind
spring
(s)
read
and fo
llow the
direc tions in th e
installat
ion instru
ctions /owner
s
manu al.
DO N OT R EMO VE T HIS T AG.
WINDING ShAfT
CABLE
DRuM
GROOVE
ROuND NOTCh
fLAGANGLE
SPLINES
COuNTERBALANCE CABLE
GROOVE
CABLE
DRuM
SPLINES
WINDING ShAfT
Right Drum TorqueMaster ® Spring Tube
Assembly
Right Drum TorqueMaster ® Spring Tube
Assembly
1/2 wrap Shown
1-1/2 wrap Shown
Counterbalance Cable
Counterbalance Cable