Extron Electronics PVS 405D User Guide User Manual
Page 32
Command
ASCII Command
(host to switcher)
Response
(switcher to host)
Additional Description
EDID Minder
NOTES:
•
The switcher and PVT wallplate have two default EDIDs: 720p @ 60 Hz (digital), and 1024x768 @ 60 Hz (analog).
•
The default EDID of 720p @ 60Hz, 2‑CH is always present at inputs 1‑4 when no PVT wall plates are detected.
•
The firmware automatically uses default EDID of 1024x768 @ 60Hz for inputs 2 and 4 when a PVT SW HDMI RGB
D wall plate is detected
•
on page 19 for X1* SIS symbol definitions.
Assign EDID to
inputs
E
AX1!*X1*EDID}
EdidAX1!*X1*]
Assign EDID resolution and refresh rate
X1*
for input
X1!
.
View assigned EDID
data
E
AX1!EDID}
EdidAX1!*X1*]
EdidAX1!*X1*]
View assigned EDID resolution and
refresh rate
X1*
for input
X1!
.
Verbose mode response
Capture display
EDID to custom
(user) slot (1‑4)
E
SX1*EDID}
EdidSX1*]
Capture display EDID to
X1*
.
View/read EDID in
HEX format
E
RX1!EDID}
X2)]
View assigned EDID resolution and
refresh rate
X2)
in HEX format.
View/read EDID
native resolution
E
NX1!EDID}
X2!]
View assigned EDID native resolution
X2!
.
HDCP status
View input HDCP
E
IX1(HDCP}
HdcpIX1(*X1%]
Query the input HDCP status
X1%
of the
current input
X1(
.
View output HDCP
E
OHDCP}
HdcpOX1^]
Query the HDCP status
X1^
of the HDMI
output.
View all HDMI input
HDCP
E
IHDCP}
Hdcp•X1%•X1%•X1%•X1%]
Query the HDCP status
X1%
of all the
HDMI inputs (selected PVT wallplates).
HDCP input authorization (valid for HDMI inputs only)
HDCP Authorized
device on
E
EX1(*1HDCP}
HdcpEX1(*1]
Turn HDCP Authorized on for input
X1(
(default). Enables encryption support.
HDCP Authorized
device off
E
EX1(*0HDCP}
HdcpEX1(*0]
Turn HDCP Authorized device off for
input
X1(
. Disables encryption support.
Query HDCP
Authorized Device
status
E
EX1(HDCP}
Verbose response
X1&]
HdcpEX1(*X1&]
Query HDCP Authorized device status
for input
X1(
.
NOTE:
X1!
= Input selection: 1 to 4
X1%
= HDCP source status:
0 = Source detected but not HDCP compliant,
1 = Source detected and is HDCP compliant,
2 = No source detected, 3 = Unknown
X1^
= HDCP sink status:
0 = Source detected and is encrypted, sink is connected but not HDCP compliant,
1 = Source detected and is encrypted, sink is connected and is HDCP compliant,
2 = No sink detected,
3 = Source is not encrypted or detected, sink is connected but HDCP status is unknown
X1&
= HDMI input HDCP Authorization status:
0 = Block HDCP encryption,
1 = Allow HDCP encryption (default)
X1*
= EDID values. See the
X1(
= HDCP input selection; inputs 1‑4 only.
X2)
= EDID in HEX format: 128 or 256 Byte EDID raw HEX (text form)
X2!
= Native resolution and refresh rate from selected EDID.
PVS 405D • SIS Communication and Control
26