Ransburg MGS Multi-Gun Source 76789, 77046 - Manual (Page 10)

CP-99-01
MGS Multi-Gun Source - Installation
INST INST INST INST INSTALLA ALLA ALLA ALLA ALLATION TION TION TION TION
Figure 2a: High Voltage Module Bracket Figure 2a: High Voltage Module Bracket Figure 2a: High Voltage Module Bracket Figure 2a: High Voltage Module Bracket Figure 2a: High Voltage Module Bracket
Mounting for the MGS 2000C. Mounting for the MGS 2000C. Mounting for the MGS 2000C. Mounting for the MGS 2000C. Mounting for the MGS 2000C.
Install the MGS unit (and high voltage modules for
MGS 2000C) in a convenient area outside the
hazardous location, where it will be protected from
the possibility of environmental intrusion, such as
dust or moisture, and ambient temperatures do not
exceed 120
° F. The control unit may be mounted
> As each installation is unique, this
information is intended to provide general
installation information for the MGS con-
trol unit. Consult your authorized ITW
Ransburg representative for specific di-
rections pertaining to the installation of
your equipment.
> >> > > The MGS control unit (and High Voltage
Modules for MGS 2000C) MUST
MUST MUST MUST MUST be located
outside the hazardous area. (See National
Fire Protection Association Bulletin No. 33;
the Occupational Safety and Health Act of
1970, sections 1910.106 and 1910.107 and
ITW Ransburg Bulletin,
Operating Your Elec-
trostatic Coating System Safely.)))))
> >> > > The user MUST MUST MUST MUST MUST read and be familiar with
the SAFETY SAFETY SAFETY SAFETY SAFETY and SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS
SECTIONS SECTIONS SECTIONS SECTIONS SECTIONS of this manual.
> This manual MUST MUST MUST MUST MUST be read and thorough-
ly understood by ALL ALL ALL ALL ALL personnel who operate,
clean or maintain this equipment! Special care
should be taken to insure that the WARN-
WARN- WARN- WARN- WARN-
INGS INGS INGS INGS INGS and requirements for operating and
servicing safely are followed. The user should
be aware of and adhere to ALL
ALL ALL ALL ALL local building
and fire codes and ordinances as well as
NFPA Standard 33 and The Occupational
Safety and Health Act of 1970 (OSHA) prior to
installing, operating and/or servicing this equip-
ment.
> DO NOT DO NOT DO NOT DO NOT DO NOT locate the control unit (or high
voltage modules for MGS 2000C) near or
adjacent to heat producing equipment such as
ovens, high wattage lamps, etc.
The high voltage modules should be mounted in
an upright position ONLY. The mounting bracket
76086-00 (supplied) can be used to mount the
high voltage modules.
To mount the high voltage module, first install the
76086-00 brackets as shown in Figure 2a. Then,
lift the high voltage module so that it's handle can
be inserted into the bracket slot, as shown in
Figure 2b. Next, lower the bottom of the high
voltage module until the handle comes forward in
the slot and the back of the module rests against
the wall.
N O T E N O T E N O T E N O T E N O T E
LOCA LOCA LOCA LOCA LOCATION TION TION TION TION
on the booth wall or where a convenient booth wall
penetration may be made.
W A R N I N G W A R N I N G W A R N I N G W A R N I N G W A R N I N G
!
C A U T I O N C A U T I O N C A U T I O N C A U T I O N C A U T I O N
!
For MGS 2000C For MGS 2000C For MGS 2000C For MGS 2000C For MGS 2000C
6 6 6 6 6
ARCHIVE