TOHO ELECTRONICS TTM-509 User Manual
Page 65
TOHO
TOHO ELECTRONICS INC.
DWG. No.
45-4199-E
PAGE
65/66
30)
P55: Communications speed: "Infrared communications cannot select 4,800bps" was deleted.
31)
P57: The auxiliary screen was changed to .
32)
P61: The designation , which had been "First setting for logging," was corrected to
"Ninth."
33)
P62: "Set the operation mode display" was added.
Revision B, May 20, 2004, Ishihara
34)
The method of setting cascade and remote control were changed. The system was changed from
setting by input type to setting by control type.
35)
P51: The setting range for event output sensitivity was changed from "-19999 to 99999" to "0 to
99999."
36)
P49: The setting range of the dead band was changed from "-10000 to 10000" to "-19999 to 19999."
37)
P44, 52, and 53: The need of the difference of 50 digits for SLL/SLH, CASL/CASH, REL/REH, and
TRL?/TRH?/TRL/TRH (for transmission only) was eliminated.
38)
P52 and 53: The "Set the transmission output" includes MV transmission but not the setting of the
main output and auxiliary output. They were then added.
39)
P53: The setting of 1 CH and 2 CH were added to "Set a transmission output function."
40)
P56: The method of setting a timer function was changed. Provision was made so that setting a
time would activate the timer instead of determining an ON/OFF delay with the timer function.
41)
P19 and P43: There had been two buzzer settings. One of them was removed.
42)
P63: The way a blind enters and other details were added.
43)
P50: An OUT setting was determined in the case of a potentiometer (position proportional control).
44)
P36: Final line: "▲= in the case of CH 1 polygonal approximation" was changed to "▲= in the
case of CH 2 polygonal line approximation."
45)
P47: The setting ranges for "Set the main control operation amount change limiter to rise, to fall, "
"Set the auxiliary control operation amount change limiter to rise, to fall" were changed to "0 to
110.0" to "0 to 120.0." "Limitless at 0.0" was deleted. The initial value was set to 100.0.
46)
P48: The description of the potentiometers for "Set a main output sensitivity," "Set an auxiliary
output sensitivity," "Position the OFF point of the main output," and "Position the OFF point of the
auxiliary output" was deleted.
47)
P49: In the case of a potentiometer, the dead band setting was changed to the differential gap
(sensitivity) of the potentiometer.
48)
P54: In a DI, "Start AT and start the timer" was changed to "Input a level."
49)
P54: In RUN/RDY and Auto/Manual with DI input, the non-active state was changed from "fixed"
(such as RUN) to a state.
50)
P45: The "timer connection channel" setting was added to "Set a control type." This enables the time
to be finished in CH 1 and CH 2 at the same time.
51)
P56: was deleted.
52)
P50: ": Connect it to the timer" was added to "Set a function for event outputs 1 to 6."
53)
P13 and 14: A change was made so that a control state when the system was turned on would be
determined by a startup setting state. It was made the same as the repetition timer.
54)
P13: The description in 4.2.1 was changed.
55)
P42, 43, 46, 51, 56, 59, and 60: The upper limit of the setting range of the potentiometer was
changed from 199.9 to 999.9. The aim was to prevent limitation due to input switchover or
something similar.