Turbo Action 70600 CHEETAH E-SHIFT Controller - Manual (Page 15)

15
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
Turn Function Switch knob clockwise until the right
LED display position digits read 15.This position sets relays
to Holding Relays (H) or Pulsing Relays (P). Also, Factory
Reset for all defaults can be set in this position Fig. #17.
Factory Default = H (Fig. #17)
Program Position #15:
Push either the 1000’s or the 100’s Button, it will cycle
between H & P.
Note: Turbo Action CHEETAH E-SHIFT Electronic
Valve Bodies require Holding Relays. Shift
Lights and Air or Electric Shifters require
Pulsing Relays.
Restore Factory Defaults:
Set Function Switch to Position #15 and press Reset
Button for 5 seconds.
Turn to #0 position after making your changes.
Position #0, UPDATE Function
After any change to positons 1-15 your controller will
update all new entries.
Display will read uPd1 then uPd2 until it is finished updating
(Fig. #18)
Display will go back to “0” when complete.
NOTE: Position #0 will read RPM of the engine if in the race mode. Depending on how many
cylinders your engine has, a minimum engine RPM required to produce a readout.
Minimum RPM per number of cylinders:
Cylinders RPM Minimum for a Display
2 1500
4 750
6 500
8 370
10 300
H 1 5
10K 1K 100 POS. POS.
Fig. #17
POSITION #15: Controller Relays
u P d
10K 1K 100 POS. POS.
Fig. #18
1
1/99,6/99