Avaya IP OFFICE 40DHB0002USCL - Manual (Page 15)

IP403 Office Platform IP403 Office - Front View - Page 15
IP403 Office - Front View
Yellow LEDs
LEDs 1-3 = Expansion Ports 1-3 status
LEDs 4-7 = ISDN 1-4 status
LED 8 = WAN status
Green LEDs
Terminal connected
DT or DS Ports 1-8
Unit Status LED
Red = Alive but not initiated
Green = Running OK
Phone Ports 1& 2
(POTs) LAN Ports 1-8
Port 8
(Cascade port)
Yellow LED
LAN Collision
Green LED
Solid Green LED - LAN OK
Flashing Green - LAN OK and active
Yellow LED
On - 100Mbps operation
0ff - 10Mbps operation
Cascade Switch
For port eight
Port connections
• DT/DS Ports
- DT ports are for connection to Avaya 2000 series telephones (see page 5).
- DS ports are for connection to Avaya 4400 and/or 6400 series telephones (see page 5).
At default DT ports are set to A-Law PCM encoding and DS ports to either A-Law or
µ-Law PCM encoding (see page 32). However, both ports can be switched in software -
refer to the Administration Manager Manual for details).
Using DT Line Cords (see page 56) and standard structured wiring, these RJ45 ports can be
extended to the required telephone location. In addition, converters can be used to provide BT
New Plan sockets (431A/631A) if required (see page 65). When telephones are equipped with
line cords that terminate in RJ11 plugs, then pin-to-pin RJ11/RJ45 adapters should be used.
• Plain Ordinary Telephone (POTS) Ports
These two ports are used for connection to standard analog telephones, fax machines and
modems. Using standard structured wiring, these RJ45 ports can be extended to the required
telephone location. Converters can be used to provide BT New Plan sockets (431A/631A) if
required (see page 65). When devices are equipped with line cords that terminate in RJ11 plugs,
then pin-to-pin RJ11/RJ45 adapters should be used.
• LAN Ports
The eight auto-negotiating 10/100 BaseT LAN hub ports are used for PC and server connectivity.
They can also be used to connect to the optional IP400 WAN3 Expansion Module (see page 30)
and IP telephones. LAN ports allow information relating to incoming and outgoing telephone calls
to be forwarded to PC based applications. They also provide access to the router
functionality/configuration of the IP403 Office platform for both data and Voice over IP (VoIP)
calls. (Where IP telephony is required, a suitable switch, i.e. an Avaya Cajun P130, should be
used.) This eight port auto-negotiating 10/100 BaseT LAN hub has a single MAC address (printed
on the base of the unit).
Where more than eight LAN connections are required, the eighth LAN port can be used for
cascading to other hubs. The Cascade pushbutton to the right of this port is used to set the
mode. When the Cascade switch is in the out position the port can be connected to another hub
without the need for a crossover cable, i.e. the port is an MDI type port. When the Cascade
switch is in the in position the port can be connected directly to a PC.
Cables
IP403 Office DT PRI 30 E1 & DS PRI 24 T1 are supplied with one red ISDN cable. IP403 Office DT
BRI 8 & DS Analog 4 are supplied with four red ISDN cables. For Port Pinouts and Cables, refer to
pages 51 and 55 respectively.
IP Office Installation Manual IP403 Office Platform - Page 15
40DHB0002USCL – Issue 7 (09/25/2002) IP403 Office - Front View