Vaddio ZoomSHOT WallVIEW USB - Manual (Page 30)

ZOOMSHOT WallVIEW USB Camera System
ZoomSHOT WallVIEW USB System Document Number 342-0640 Rev. B Page 30 of 40
C OMMUNICATION S PECIFICATION
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control
NOTE: The Vaddio ZoomSHOT control protocol is similar to, but not identical to the Sony® VISCA™ command
set in order to be compatible with several popular control devices. Not all VISCA commands are supported and
there are ZoomSHOT specific commands in the following Command and Inquiry Lists.
ZoomSHOT Command List (1/2)
Command Set Command Command Packet Comments
Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On
Off(Standby)
8x 01 04 00 02 FF
8x 01 04 00 03 FF Power On/Off
CAM_Zoom Stop
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Direct(Variable)
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 00 0p 0q 0r FF
8x 01 7E 01 4A 0v 0p 0q 0r 0s FF
p:(0-Slow to 7-Fast)
pqrs: Zoom Position
*
v: zoom speed
CAM_Focus Stop
Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
pqrs: Focus position
*
CAM_WB Auto
Manual
One Push WB
8x 01 04 35 00 FF
8x 01 04 35 05FF
8x 01 04 35 03 FF Normal Auto (Auto Tracing WB)
Manual White Balance
One Push White Balance Mode
CAM_RGain Reset
Up
Down
Direct
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 0p 0q 0r 0s FF
pqrs:00-ffff
CAM_BGain Reset
Up
Down
Direct
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 0p 0q 0r 0s FF
pqrs:00-ffff
CAM_AE Full Auto
Manual
8x 01 04 39 00 FF
8x 01 04 39 03 FF Auto Exposure Mode
Manual Control Mode
CAM_Iris Reset
Up
Down
Direct
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
pq(0x00-0x11)
CAM_Gain Reset
Up
Down
Direct
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
pq(0x00-0x11)
CAM_Bright Reset
Up
Down
Direct
8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF
pq(0x00-0x24)
CAM_Backlight On
Off
8x 01 04 33 02 FF
8x 01 04 33 03 FF
CAM_Aperture Reset
Up
Down
Direct
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
pq(0x00-0x1F)
Pin # RJ-45 RS-232 and IR Out Pins
1) Unused
2)
Unused
3) Unused
4)
IR Output (Diff Signal used with Quick-Connect SR)
5) IR Ground (Diff Signal used with Quick-Connect SR)
6) GND (GND of IR Short Range - Pin 3)
7) RXD (from TXD of control source)
8) TXD (to RXD of control source)
12345678