Literature, hardware and tools parts list, Sawstop, No. description part no. qty – SawStop CNS175-AU User Manual
Page 104: 10” contractor saw
102
SawStop 10” Contractor Saw
Literature, Hardware and Tools Parts List
No.
Description
Part No.
Qty.
1
SawStop 10” Contractor Saw Owner’s Manual
CNS-10-005
1
2
Assembly Instructions Poster
CNS-07-248
1
3
Push Stick
CNS-10-007
1
4
Hardware Pack #1
CNS-07-250
1
5
Hardware Pack #2 (includes items 6-9)
CNS-07-251
1
6
3 mm Hex Key
CB104 268
1
7
5 mm Hex Key
CB104 269
1
8
8 mm Hex Key Ball End
CB104 270
1
9
Blade Spacing Adjustment Gauge
CNS-07-255
1
OWNER’S MANUAL
10” CONTRACTOR SAW
SawStop
®
1
2
3
4
5
6
7
8
9
Assembling Your SawStop Contractor Saw
SawStop Service Department
503-582-9934
www.sawstop.com
Before assembling your saw, make sure that you
have all the components identified on pages 12 and
13 in the Owner’s Manual, including hardware
pack #1 and hardware pack #2. Call the SawStop
Service Department at 503-582-9934 if any
components are missing. Hardware pack #2
includes some of the tools needed to assemble
the saw. You will also need the following additional
tools:
1. an 8 mm socket
2. a 10 mm wrench
3. two 13 mm wrenches
4. a level or straight edge
Assembling the Stand
1
• Locate the stand components labeled through and
hardware pack #1. All of the hardware needed to assemble the
stand is located in the area with the blue background on
hardware pack #1. In order to easily identify the hardware used
in each of the following steps, the different pieces of hardware
are numbered on the hardware pack and on these assembly
instructions.
A
F
2
• Assemble the front of the stand by attaching two of the legs
marked to the front panel marked . Make sure that the legs
are in front of the front panel. Bumps on the legs fit into holes in
the front panel to align the legs. Attach the legs to the front
panel using four M8 x 20 carriage bolts , four M8 washers ,
four M8 lock washers , and four M8 hex nuts . Do
not fully
tighten the nuts at this time. Leaving the nuts loose will make it
easier to align holes as you assemble the rest of the stand.
4
3
2
1
A
B
A
B
1
2
3
4
A
3
4
3
2
1
• Assemble the rear of the stand by attaching the remaining two
legs marked to the rear panel marked . Make sure that the
legs are in front of the rear panel. Bumps on the legs fit into holes
in the rear panel to align the legs. Attach the legs to the rear
panel using four M8 x 20 carriage bolts , four M8 washers ,
four M8 lock washers , and four M8 hex nuts . Do
not fully
tighten the nuts at this time.
A
C
A
C
A
1
2
3
4
4
• Attach one of the side panels marked between the front and
rear portions of the stand. Make sure the legs are in front of the
side panel and that the side panel is under the top flanges of the
front and rear panels. Bumps on the legs fit into holes in the side
panel to align the legs. Use four M8 x 20 carriage bolts ,
four M8 washers , four M8 lock washers , and four M8 hex
nuts to attach the side panel to the front and rear portions.
Do
not fully tighten the nuts.
4
3
2
1
D
D
1
2
3
4
5
• Repeat the prior step to attach the remaining side panel
marked to the opposite side of the stand.
1
2
3
4
D
D
6
• Attach one long bracket marked between the legs on the
right side of the stand. Make sure the legs are in front of the
brackets. Use two M8 x 20 carriage bolts , two M8 washers ,
two M8 lock washers , and two M8 hex nuts to attach the
long bracket. Do
not fully tighten the nuts. Repeat this process
to attach the remaining long bracket between the legs on the
left side of the stand.
1
2
3
4
7
F
4
3
2
1
F
8
• The front, rear and side panels have flanges that overlap to
define mounting holes through which you will bolt the saw to
the stand. There is one hole in each corner of the stand.
Adjust the panels until the holes align and then tighten all of
the nuts in the stand using a 13 mm wrench.
9
4
2
2
4
5
• Attach a foot to the bottom of
each leg by threading an M8 hex
nut on each foot and then
placing an M8 washer over
the nut. Insert a foot into the hole
at the base of each leg and then
place a second M8 washer and
thread a second M8 hex nut
onto each foot. Do
not fully
tighten the nuts. The stand is
now fully assembled.
Note: If you purchased an optional
mobile base for your saw, install it
now by following the instructions
that came with the mobile base.
4
2
2
4
5
Mounting the Saw
to the Stand
10
• Remove the saw from the box and locate the
mounting hardware. All of the hardware needed to
mount the saw to the stand is located in the area with
the yellow background on hardware pack #1.
11
• With the help of an assistant, pick up the saw and carefully set it
on the assembled stand with the front of the saw above the front
panel of the stand. Align the mounting holes in the bottom corners
of the saw with the mounting holes in the top corners of the stand.
While moving the saw do not set it down in the upright position on
a solid surface because the dust shroud can be damaged.
Warning! The saw weighs approximately 140 pounds. Be careful
and use proper lifting technique to avoid injury.
• Attach one of the short brackets marked between the two
front legs. Make sure the legs are in front of the bracket. Use
two M8 x 20 carriage bolts , two M8 washers , two M8 lock
washers , and two M8 hex nuts . Do
not fully tighten the
nuts. Repeat this process to attach
the remaining short bracket
between the rear legs.
E
1
2
3
4
1
2
4
3
E
E
mounting holes
0
15
30
45
SawStop
10”Contractor
Saw
0
15
30
45
SawStop
10”ContractorS
aw
Mounting the Saw to the Stand
Washers, M8
(32 + 2 extra)
Lock Washers, M8
(24 + 2 extra)
Assembling the Stand
Hex Nuts, M8
(32 + 2 extra)
Leveling Feet
(4)
Hardware for Steps 10-14
Hardware for Steps 1-9
Carriage Bolts, M8 x 20
(24 + 2 extra)
1
2
4
5
3
Hex Screws,
M8 x 20 (4)
6
Lock Washers,
M8 (4)
8
Hex Nuts,
M8 (4)
9
Washers,
M8 (8)
7
Hardware Pack #1
Mounting the Saw to the Stand
Washers, M8
(32 + 2 extra)
Lock Washers, M8
(24 + 2 extra)
Assembling the Stand
Hex Nuts, M8
(32 + 2 extra)
Leveling Feet
(4)
Hardware for Steps 10-14
Hardware for Steps 1-9
Carriage Bolts, M8 x 20
(24 + 2 extra)
1
2
4
5
3
Hex Screws,
M8 x 20 (4)
6
Lock Washers,
M8 (4)
8
Hex Nuts,
M8 (4)
9
Washers,
M8 (8)
7
Hardware Pack #1
F
Flip to
Other Side
© SawStop, LLC
Mounting the Saw to the Stand
Washers, M8
(32 + 2 extra)
Lock Washers, M8
(24 + 2 extra)
Assembling the Stand
Hex Nuts, M8
(32 + 2 extra)
Leveling Feet
(4)
Hardware for Steps 10-14
Hardware for Steps 1-9
Carriage Bolts, M8 x 20
(24 + 2 extra)
1
2
4
5
3
Hex Screws,
M8 x 20 (4)
6
Lock Washers,
M8 (4)
8
Hex Nuts,
M8 (4)
9
Washers,
M8 (8)
7
Hardware Pack
#
1
Tools
Hex Key, M3
(1)
Hex Key, M5
(1)
Hex Key, M8
(1)
Mounting the Switch Box
Hardware for Step 22
Switch Box Keys
(2)
Washers,
M6 (2)
14
Hex Screws,
M6 x 20 (2) 15
Installing the Motor and Belt Guard
Hardware for Steps 17-19
Washers, M5 (4)
10
Hex Nuts, M5 (4) 11
Mounting the Extension Wings
Hardware for Steps 20-21
Lock Washers,
M8 (8)
12
Hex Screws,
M8 x 16 (8) 13
Hardware Pack
#
2
Blade Spacing
Adjustment
Gauge
(1)