Using subwoofer output, Using non fading output, Adjusting loudness – Pioneer AVIC-HD3 User Manual
Page 136: Using the high pass filter
134
Ch
ap
te
r
14
Cu
st
om
isin
g t
h
e A
u
d
io
S
et
tin
g re
la
te
d
wi
th
A
u
d
io
V
is
u
al
AV
When the rear output setting is Rear SP
Sub.w, you cannot adjust front/rear speaker
balance.
➲
“Setting the rear output and subwoofer
controller” ➞ Page 140
3
Touch 4 or 6 to adjust left/right speaker
balance.
Each time you touch 4 or 6 moves the left/
right speaker balance towards the left or the
right.
Left: 9 to Right: 9 is displayed as the left/
right speaker balance moves from left to right.
Using subwoofer output
The navigation system is equipped with a sub-
woofer output which can be turned on or off.
❒
When the subwoofer output is on, you can
adjust the cut-off frequency, the output level,
and the phase of the subwoofer.
1
Touch [Sub Woofer] in the Audio Settings
menu.
When Preout (the subwoofer controller set-
ting in System Settings menu) is Full, you
cannot select [Sub Woofer].
➲
“Setting the rear output and subwoofer
controller” ➞ Page 140
2
Touch [On] to turn subwoofer output on.
To turn subwoofer output off, touch [Off].
3
Touch [Reverse] or [Normal] to select the
phase of subwoofer output.
❒
If subwoofer output sound is not clear with
[Normal], change it to [Reverse].
4
Touch 4 or 6 to select cut-off frequency.
Each time you touch 4 or 6 selects cut-off
frequencies in the following order:
50 – 80 – 125 (Hz)
Only frequencies lower than those in the
selected range are output from the subwoofer.
5
Touch [+] or [–] to adjust the output level
of the subwoofer.
+6 to –6 is displayed as the level is increased
or decreased.
Using non fading output
When the non fading output setting is on, the
audio signal does not pass through the naviga-
tion system’s low pass filter (for the subwoofer),
but is output through the RCA output.
1
Touch [Non Fading] in the Audio Settings
menu.
Only when Preout (the subwoofer controller
setting in System Settings menu) is Full,
you can select [Non Fading].
➲
“Setting the rear output and subwoofer
controller” ➞ Page 140
2
Touch [On] to turn non fading output on.
To turn non fading output off, touch [Off].
3
Touch [+] or [–] to adjust the output level
of the non fading.
+6 to –6 is displayed as the level is increased
or decreased.
Adjusting loudness
Loudness compensates for deficiencies in the
low- and high-sound ranges at low volume.
1
Touch [Loudness] in the Audio Settings
menu.
2
Touch [On] to turn loudness on.
To turn loudness off, touch [Off].
3
Touch 4 or 6 to select a desired level.
Each time you touch 4 or 6 selects level in
the following order:
Low – Mid – High
Using the high pass filter
When you do not want low sounds from the sub-
woofer output frequency range to play from the
front or rear speakers, turn the HPF (high pass fil-
ter) on. Only frequencies higher than those in the
selected range are output from the front or rear
speakers.
1
Touch [HPF] in the Audio Settings menu.
2
Touch [On] to turn high pass filter on.
To turn high pass filter off, touch [Off].
MAN-HD3-SOFTW-EN.book Page 134 Wednesday, January 10, 2007 9:33 AM