Specifications, Remote control unit, Rf adapter – Pioneer CU-RF100-U User Manual
Page 27: Note, Additional information 05, English
Additional information
05
27
En
English
Specifications
Remote control unit
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 3 V
Estimated line-of-sight transmission distance*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 10 m
Radio frequency band . . . . . . . . . . . . . . . . 2.4 GHz
Modulation system
. . . . . .Direct Sequence Spread Spectrum (DSSS)
Dimensions
. . . . . . . . . . 51 mm (W) x 255 mm (H) x 34 mm (D)
(2
1
/
16
in. (W) x 10
1
/
16
in. (H) x 1
3
/
8
in. (D))
Weight . . . . . . . . . . . . . . . . . . . . . . . . 190 g (0.4 lb)
RF adapter
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 5 V
Estimated line-of-sight transmission distance*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 10 m
Radio frequency band . . . . . . . . . . . . . . . . 2.4 GHz
Modulation system
. . . . . .Direct Sequence Spread Spectrum (DSSS)
Dimensions
. . . . . . . . . 49 mm (W) x 21 mm (H) x 64.5 mm (D)
(2 in. (W) x
7
/
8
in. (H) x 2
9
/
16
in. (D))
Weight . . . . . . . . . . . . . . . . . . . . . . . . . 90 g (0.2 lb)
* The line-of-sight transmission distance is an
estimate. Actual transmission distances
supported may differ depending on surrounding
conditions.
Note
• Specifications and the design are subject
to possible modifications without notice,
due to improvements.
Published by Pioneer Corporation.
Copyright © 2010 Pioneer Corporation.
All rights reserved.
Other components can’t be
operated with the system
remote.
• If the battery ran down, the preset codes may have been cleared. Re-enter the
preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset
codes.
• When commands from the remote control units of other devices are
registered using the learning function, in some cases they may not be learned
properly. In this case, register the commands again using the learning function
(see Programming signals from other remote controls on page 14). If they still do
not work, they may be in a special format that cannot be registered on this
receiver’s remote control. Operate the device using another remote control.
The remote control display
flickers.
• Flickering may occur when the remaining battery power is low. Replace the
batteries with new ones (see Loading the batteries on page 4).
U.S. and Canadian models
only: Input does not switch to
Sirius or XM when
OPTION 1
or
OPTION 2 button is
pressed.
• Sirius and XM operations can no longer be performed if other preset codes
are assigned to the
OPTION 1 (Sirius) or OPTION 2 (XM) button. In this case,
reset the
OPTION 1 or OPTION 2 button (see Resetting the input assignment
of one of the input function buttons on page 16).
Symptom
Remedy
05_additional_info.fm 27 ページ ２０１０年３月１７日 水曜日 午前１０時１４分