Infinity supported application 11 – AEM Infinity Supported Applications - Dodge 2008-2010 Viper 4G User Manual
Page 11
Infinity Supported Application
11
© 2014 AEM Performance Electronics
Infinity
Pin
Hardware Reference
08–10 Dodge
Viper Function
08–10
Dodge
Viper Pin
Destination
Hardware Specification
Notes
C1-18
LowsideSwitch_3
MIL Output
Lowside switch, 4A max
with internal f ly back diode.
Inductiv e load should NOT
hav e f ull time power.
See Wizard page "LowSide Assignment
Tables" f or output assignment.
MIL Activ ates when any of the
f ollowing f lags are true: ErrorAirTemp,
ErrorBaro, ErrorCoolantTemp,
ErrorEBP, ErrorFuelPressure,
UEGO_0_Diag_error,
UEGO_1_Diag_error, ErrorMAFAnalog,
ErrorMAFDigital, ErrorMAP,
ErrorOilPressure, ErrorThrottle.
C1-19
AGND_1
Sensor Ground
C1-17 / C1-
23
Dedicated analog ground
Analog 0–5V sensor ground
C1-20
AGND_1
Sensor Ground
C1-18
Dedicated analog ground
Analog 0–5V sensor ground
C1-21
Crankshaf t Position
Sensor Hall
Crankshaf t
Position Sensor
Hall
C1-25
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Cam/Crank f or
options.
C1-22
Camshaf t Position
Sensor 1 Hall
Camshaf t
Position Sensor
1 Hall
C1-22
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Cam/Crank f or
options.
C1-23
Digital_In_2
Camshaf t
Position Sensor
2 Hall
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Cam/Crank f or
options.
C1-24
Digital_In_3
Turbo Speed Hz
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Input Function
Assignment f or calibration constant.
TurboSpeed [RPM] = Turbo [Hz] * Turbo
Speed Calibration.
C1-25
Digital_In_4
Vehicle Speed
Sensor
C4-29
10K pullup to 12V. Will work
with ground or f loating
switches.
See Setup Wizard page Input Function
Assignment f or calibration constant.
C1-26
Digital_In_5
Flex Fuel
10K pullup to 12V. Will work
with ground or f loating
switches.
See channel FlexDigitalIn [Hz] f or raw
f requency input data.
C1-27
Knock Sensor 1
Knock Sensor 1
C3-34
Dedicated knock signal
processor
See Setup Wizard page Knock Setup
f or options.
C1-28
Knock Sensor 2
Knock Sensor 2
C3-26
Dedicated knock signal
processor
See Setup Wizard page Knock Setup
f or options.
C1-29
+12V_Relay _Control
+12V Relay
Control
C3-19 / C2-
17
0.7A max ground sink f or
external relay control
Will activ ate at key on and at key of f
according to the conf iguration settings.
C1-30
Power Ground
Ground
C3-27
Power Ground
Connect directly to battery ground.
C1-31
CANL_Aout
AEMNet CANL
Dedicated High Speed CAN
Transceiv er
Recommend twisted pair (one twist per
2") with terminating resistor. Contact
AEM f or additional inf ormation.