Sony SLV-789HF - Manual (Page 5)

SECTION 1
GENERAL
SLV-789HF/792HF/799HF
This section is extracted from
instruction manual.
c
Getting Started
Step 1
Unpacking
Chect that you have received the following iteiris with the VCR:
• Rentote commander • Cable Mouse (cable box controller)
* Siz< AA (R6) batteries ■ 75-ohm coaxial cable with F-type
connectors
’ Audio/video cable (3-phono, 1-mini
to 3-phono, 1-mini)
A
Step 2
Setting up the remote commander
Inserting the batteries
Insert two size AA (R6) batteries
by nratching the + and — on the
batteries to the diagram inside the
battery compartment.
Insert the negative (-) end first,
then push in and down until the
positive (-♦-) end dicks into position.
Using the remote commander Remote sensor
You can use tliis remote
commander to operate this VCR
and a Sony TV or AV receiver.
Buttons on the remote
commander marked with a dot
(•) can be used to operate your
Sony TV.
The RECEIVER VOL +/- and
MUTING buttons can be used to
operate your Sony AV receiver.
RECEIVER VOL+/-
To operate Set [RECEIVE r I <(VÍD' e 6| to
and point at the remote sensor on the VCK
a Sony TV
or a V receiver
ITVIIRECEIVERI and point at Uie remote sensor on the TV or AV
receiver
4 j Gettini) Started
Getting Started | 5
5fep 2; Setting up the remote commander (continued)
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery Icakage.
• LX) not use a new battery with an old one.
• Do not use different types of batteries.
• Some Sony AV receivers may not be operated with the remote commander.
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the table below, set the appropriate nuinufacturer's code
number.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
Set rfVliRECEfVHRi/IVrDEOl at tlie top of the remote commander to
I
tv II rëœîver T
Hold down l/d), and enter your TV's code nuntber(s) using the number
buttons. Then release
I/Ô.
Now you can use the 1/(1), VOL +/-, CH +/-, and TV/VIDEO buttons to
control your TV. You can also use the buttons marked with a dot {•) to
control a Sony TV. To control the VCR, reset ITv IfRECEIVE^ / IVIDE(5lto
L vided J -
Manufacturer Code
number Manufacturer Code
number Manufacturer Code
number
Sony 01 JVC 09 RCA 04,10
Akai 04 KMC 03 Sampo 12
AOC 04 Magnavox 03, 08,12 Sanyo 11
Centurion 12 Marantz 04,13 Scott 12
Coronado 03 MGA/Mitsubishi W,12,13,17 Sears 07,10,11
Curis-Mathes 12 NEC 04,12 Sharp 03, 05,18
Daytron 12 Pataasonic 06,19 Sylvania 08,12
Emerson 03,04,14 PhiJeo 03,04 Teknika 03, 08,14
Fisher 11 Philips 08 Toshiba 07
General Electric 06,10 Pioneer 16 Wards 03, 04, 12
Gold Star 03,04,17 Portland 03 Yorx 12
Hitachi 02,03 Quasar Û6, 18 /.enith 15
J.C.I’cnny 04,12 Radio Shac k 05,14
Notes
• If the TV uses a different remote coninil system from tlie one pn>grammeil to work
witli the VCR, you carmot control your TV witli the remote comirrander.
• If you enter a new code number, the code number previously entered will be erased.
• When you replace the batteries of the remote commander, the code numlx;r may
change. Set the appropriate code number every time you replace tlie batteries.
A