Sage Oracle BES980UK - Manual (Page 12)

23 24
PAge heAder..... PAge heAder..... oPErAtIng yoUr nEW APPLIAnCE
Water Hardness (Hrd3)
Please refer to page 14 to first determine
water hardness with the test strips provided.
To set water hardness rotate SELECT dial to
select from settings Hrd1 - Hrd5.
1 = softest and 5 = hardest.
Push SELECT dial to save setting. Machine
will beep once to confirm, then proceed to
STANDBY mode.
Units (SEt)
Set units to metric or imperial. Rotate
SELECT dial counter-clockwise to select
required units. Press SELECT dial to set.
Machine will beep once to confirm selection.
LCd Backlight (Lcd)
Adjust the LCD brightness/contrast.
Rotate SELECT dial the select required
brightness. Press SELECT dial to set.
Machine will beep once to confirm selection.
Spotlights (SPot)
SPOT adjusts the brightness of the LEDS
lighting the drip tray area. Rotate SELECT
dial the select required brightness.
Press dial to set. Machine will beep once
to confirm selection.
Steam temperature (StEA)
Adjust the steam boiler temperature,
which in turn controls steam pressure. Press
SELECT dial. Rotate SELECT dial the select
required temperature. Press SELECT dial
to set. Machine will beep once to confirm
selection. Default is 135˚C.
Air Pump delay (Air)
Adjust the delay of the operation of the
Air Pump during Automatic Milk Texturing.
Rotate SELECT dial the select required
delay. Press SELECT dial to set. Machine
will beep once to confirm selection. default
setting is 02 50˚C .
Sound Volume (Snd)
Machine sounds turned High, Low or OFF.
fan Control (fAn)
Adjust the speed of the internal cooling fan.
Rotate SELECT dial the select required fan
speed. Select between Silent (SILt), Standard
(StNd) or Cool. Press SELECT dial to set.
Machine will beep once to confirm selection.
Auto Clean disable (Cln)
Disables the Auto Clean alert. Rotate
SELECT dial between ON to activate
(default) or OFF to disable.
12h or 24h Clock (CLoC)
Select between displaying time in 12h
or 24h format. Rotate SELECT dial the select
required unit. Press SELECT dial to set.
Machine will beep once to confirm selection.
notE
The machine will exit Advanced
Features if no user input for 30 seconds
or the POWER button or MENU|EXIT
button is pressed.
flow measurement method (fLo)
Select between volume based (VOL) or
time based (SEc) method for espresso
dose measurement. Rotate SELECT dial
and select required method. Press SELECT
dial to set. Machine will beep once to
confirm selection.
ALErtS
mAnUAL will flash on StEAm LCd
The machine will not enter START UP
mode when the STEAM LEVER is in the
MANUAL position.
Move STEAM LEVER to CLOSED position
oPErAtIng yoUr nEW APPLIAnCE
for the machine to enter START UP mode.
"Manual" will flash on LCD to indicate the
lever is in the MANUAL position.
fill tank
The machine will detect a low water level.
The FILL TANK icon will flash on the
LCD screen.
If FILL TANK icon is displayed, add water
to tank . Machine will not be able to make
coffee, or hot water while tank is empty.
Clean me!
The machine will detect when 200
extractions have been carried out since
the last clean cycle.
The CLEAN ME! icon will be displayed on
the LCD screen the next time the machine
enters START UP mode.
For information on how to clean the
machine, refer to the Cleaning Cycle
instructions on page 31.
Heating
The LCD segment will flash whilst machine
is heating up and also if temperature drops
excessively during use.
Lock Hopper
Indicates if the bean hopper has not been
properly inserted and locked into position.
Coffee grinder / tamper cannot be used
during this time. 3 beeps will sound and
LOCK HOPPER segment will flash if user
attempts to activate.
overheat Please Wait
If coffee grinder is used excessively, LCD
segment will indicate user needs to wait till
it cools. Coffee grinder / tamper cannot be
used during this time. 3 beeps will sound
and OVERHEAT PLEASE WAIT segment
will flash if user attempts to activate.
Change filter
Will prompt user to replace de-scale filter
during start up. Display prompt intervals
are set by value saved for hard water.
trAnSPortIng And StorIng
'tHE orACLE' ESPrESSo mACHInE
We recommend the boilers are drained and
emptied of water before transporting the
machine or storing for extended periods
of time.
This procedure is also intended as an
anti-freeze measure in the event the machine
is exposed to extreme cold temperatures.
The procedure for draining boiler uses Step
1 and 2 of the Descale function. The current
step will be displayed on the GRIND LCD.
CAUTION
Never open DESCALE ACCESS valves
while machine is still hot. Allow
machine to cool for 1 hour prior to
starting de-scale process.
CAUTION
During de-scale process, water may
flow through group head at any time.