N ~ l t u, Date – Panasonic NV-J35 User Manual
Page 13
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Setting the Clock to the Present Time Using the Bar
Codes
0
d
9
?
?
mm
I iiH K m
____ _
* ..
I IM s Mt
1 OMMW
IMM
::: 111 n IM a IH
X m n nil
4 o HIM
■
□
raw
i: M ■ HI ■ lil
3 m I nil
r z; giHI
' = «111
n m a NM
1 1«
3! iin
1 an
• □ MIW
1 D IHW
HI a HI 3 M
IW £ na
1 = Hnu
• = IHW
T ini I im a IIH
:i: nni 1 IK
<0
mm
Mm
I MM I IIH a Ml
I IMI a iiH
MM
11 D IHW
^ HI a HI I Ml
I Mi I MU
tz iHM
•C IHW
a IM 1 NN a im
3 m I un
tD llWI
*2 %wm
I IM a IIH a Ml
IM s HI
niHt
* 2 MM
a «N a III a am
z IM e IW
■ IMHI
<c raw
IH a nil e im
] lilt ■ MM
■ o §m
•C |iM»
1 IM am a IN
3 iHi a iw
«D nni
» 2 niw
a IIH a iiN a iM
I HU a III!
II
nn
n
HM
0 IlMt
0 IIIW
a »M
3
llil
a
ail a HI
1 HM a
HU
a IM
1 m a Ml ■ IIH
\ -
□ MM
C INN
:: M a Hii ■ wi
|a m
i:: HM
c
mw
a IIH a IM a nil
■ IW D IW
IW
C IINI
c
raw
C IIIW
]
IIH
a
IIN
a
MH
a nu a HH
I
m
..H
3 IlM DM
lina
c
UWI
c liMI
D I'MW
= M c: UN :: Mi
t III!
z; MW
2
niW
SIS* 3-3=1*
- ll' ______________________ _______ 1
me
HI III
z
II
•C
IM
»n
II
I vll
-i:
til
■-
‘M
I
iH
•mZ
III
mC
in
z
III
>i*= III
■>:
III
1
'IW
mZ
'in
-C
ll>
I
'IK
■«Z
!|I1
mZ
UN
z til
™iC
HI
mZ
11
I
III
>•: tin mZ
ill
V
III
»1
1*1
-Z
IM
T
II
!«■=
HI!
nz lU
Z
Ml
mZ
IM
^
ni
e
o
Preparation
• Slide down the Mode Selector Cover on the Remote
Controller so that the Bar Code Reader Display can be
seen.
• Press the Digital Scanner On/Off Button to “ON”.
Q Trace the bar code “SETTING OF THE CLOCK”.
SETTING OF THE CLOCK
&
0 Trace the bar code for the year (YEAR).
0 Trace the bar code for the month (MONTH).
0 Trace the bar code for the day of the month (DATE),
0 Trace the bar code for the hour (START TIME).
START TIME
1
n n
t'UU
9 B-
0 Trace the bar code for the minute (MIN),
MIN
5
- n ~ l
t u
m
0 Press the Transmit Button on the Remote Controller
and then confirm that the time is displayed in the
Multi-Function Display of the VTR.
0
Press the Digital Scanner On/Off Button to “OFF".
• If the transmission was not received correctly, the
“Beep-Beep, Beep-Beep” sound from the VTR will warn
you. In this case, perform transmission again.
• If the Remote Controller is ¡eft with no operation per
formed for more than 4 minutes, it will automatically
switch over to the power-saving standby condition and the
lamp in the reading tip goes out. In this case, bar codes
that have already been read (but not yet transmitted to the
VTR) will be cancelled.
•The bar codes “SETTING OF THE CLOCK”. “YEAR” and
“MONTH” are located on page 3 of the Programming
Sheet.
<1
DATE
13)