Onkyo TX-SR601 - Manual (Page 32)

Configuring the speakers
Use the A and ▼ cursor buttons to select “Subwoofer”
and then use the < and >■ cursor buttons to select the
subwoofer setting.
Yes: Select when a subwoofer is connected.
No: Select when a subwoofer is not connected.
TX-SR701/701E/601/601E Remote controller
5. Use the A and ▼ cursor buttons to select “Front L/R”
and then use the M and >■ cursor buttons to select the
front speaker setting.
Large: Select if the front speakers are large sized.
Small: Select if the front speakers are small sized.
• If “No” is selected for the Subwoofer setting, this setting is
lixed to “Large.”
6. Use the A and ▼ cursor buttons to select “Center”
and then use the < and >■ cursor buttons to select the
center speaker setting.
None: Select if no center speaker is connected.
Large: Select if the center speaker is large sized.
Small: Select if the center speaker is small sized.
• if “Small” is selected for the Front setting, “Large” cannot
be selected for this setting.
7. Use the A and T cursor buttons to select “Surround L/
R” and then use the ◄ and ► cursor buttons to select
the surround speaker setting.
None: Select if no surround left and right speakers are
connected.
Large: Select if the surround left and right speakers aie large
sized.
Small: Select if the surround left and right speakers are small
sized.
• if “Small” is selected for the Front setting, “Large” cannot
be selected for this setting.
8. Use the A and ▼ cursor buttons to select “Surround
back” and then use the ◄ and ► cursor buttons to
select the surround back speaker setting.
None; Select if no surround back speaker is connected.
Large: Select if the surround back speaker is large sized.
Small: Select if the surround back speaker is small sized.
• If “None” is selected for the Surround setting, this setting
will be disabled.
• If “Sinall” is selected for the Surround setting, “Large”
cannot be selected for this setting.
9. Use the A and ▼ cursor buttons to select “Crossover”
and then use the < and >■ cursor buttons to select the
crossover frequency mode setting.
Adjustable Crossover for Bass Management
TX-SR701/701E
f. Crossover
This setting allows you to set the crossover frequency for your
speaker system. The crossover frequency is the minimum
frequency delivered to a speaker and can be set to 40 Hz, 60 Hz,
80 Hz (THX), 100 Hz, 120 Hz, or 150Hz. Select “80Hz (THX)”
if you are using a THX-certihed speaker system. This setting is
valid when “Subwoofer” is set to “Yes,” or foi' speakers that are
set to “Small,” at the “Speaker Conlig” menu. Frequencies
below this are cut from speakers set to “Small” and sent to the
subwoofer (or to speakers set to “Large”).
Note:
When “Large” is set, the complete fiequency range for that
speaker channel will be output. When “Small” is set, the
frequencies below 80 Hz for that speaker channel are output to
the subwoofer. If Subwoofer is set to “No” in the Speaker
Config menu, then they will be output to the left and right front
speakers. (Set all speakers for THX speaker systems to “small.”)
TX-SR601/601E
f. Crossover
This setting allows you to set the crossover frequency for your
speaker system. The crossover frequency is the minimum
frequency delivered to a speaker and can be set to 60 Hz, 80 Hz,
100 Hz, 120 Hz, or l50Hz. This setting is valid when
“Subwoofer” is set to “Yes,” or foi' speakei's that are set to
“Small,” at the “Speaker Conlig” menu. Frequencies below this
are cut from speakers set to “Small” and sent to the subwoofer
(or to speakers set to “Large”).
The following table lists the crossover frequency you should
choose depending on the diameter of your front spekers.
Front speaker diameter crosscover frequency
Larger than 12" (30cm) 40
8"~J2" (20-30 cm) 60
6-l/2”~8" (16-20 cm) 80
5-l/4"--6-J/2" (13-16cm) 100
3-l/2”~5-l/4" (9-13 cm) 120
Less than 3-1/2" (9 cm) 150
Note:
When “Large” is set, the complete fiequency range for that
speaker channel will be output. When “Small” is set, the
frequencies below 80 Hz for that speaker channel are output to
the subwoofei: If Subwoofer is set to “No” in the 1-1. Speaker
Conlig Sub-menu, then they will be output to the left and right
front speakers.
Press the RETURN button to return to the main menu.
Press the SETUP button on the front panel or on the remote
controller to exit the Setup menu.
32