Onkyo TX-SR601 - Manual (Page 45)

Selecting an Audio Component
Using the tone control;
To make bass and treble adjustment work for multichannel sources,
you must lirst set the tone control to “On.”
To turn on the tone control:
1. Press the SURROUND button (or SURR button on the
remote controller).
TX-SR701/701E/601/601E Remote controller
4
“Tone On” appears on the display and the tone control is turned
on.
2. Press the AUDIO ADJUST button and then the ▲ and
▼ cursor buttons to select Bass (orTreble).
TX-SR701 /701E/601/601E
AUDIO
ADJUST
Remote controller
AUnO ADJUTT
■'W'
3. Press the ◄ and ► cursor buttons to set the desired
level.
TX-SR701/701 E/601/601 E Remote controller
•I0#-
S h.
To turn off the tone control:
Press the DIRECT button.
TX-SR701/701E TX-SR601 /601E Remote
controller
“Direct” appears on the display and the tone control is turned
off.
Notes:
• (TX-SR701/70IE only) When you turn on the tone control, the
settings in “Speaker Contig” and “Speaker Distance” will be
used for multichannel playback.
• {TX-SR701/70IE only) When you play back multichannel
sources, you can select the Pure Audio mode by pressing the
PURE AUDIO button.
To exit the Pure Audio mode, press the DIRECT or
SURROUND button.
• If you change the speaker levels in step 4 above, these new
levels for multichannel sources will have no effect on the
settings at “Level Calibration.”
Switching the display
While listening to or watching an input source, you can display the
Information regarding the type of source and signal being input by
pressing the DISPLAY button on the TX-SR70I/701E/601/601E or
the remote controller.
You can set separate video displays for when the input source is set
to A.M or FM broadca.sts and for when it is set to anything else.
TX-SR701/701E/601601 /601E Remote controller
+10
When an input source other than FDA or AM is selected;
Input + volume | /■■■, / ¡i-,
i t
Program format or ,
sampling L‘
frequency*
i t
Input + Listening i.............. . „ „ . „
mode or Multich | r.-- v i.-- l -- ¡...i j. l .-- ________
* When the input signal is digital audio
The program format is displayed. For example, the display
“Dolby D: 3/2.1” shows that the format is Dolby Digital with
5.1 discrete channels consisting of three front channels (front
left, front right, and center), two surround channels (surround
left and surround right), and the low frequency effect (LFE)
channel.
When the front channel number is 2, they are the front left and
front right; when it is 1, it is monaural. When the surround
channel number is 1, it is monaural; when it is 0, there is no
surround channel. When the LFE number is 0, there is no LFE
channel. Also, if there is no program format for the input signal,
nothing will be displayed.
When the input signal is linear PCM
The sampling frequency is displayed. For example, the display
“PCM fs; 44.1k” shows that the signal is PCM and that the
sampling frequency is 44.1 kHz.
When FM or AM is selected as the input source:
FWAM frequency + I .Q.'.'i i f i M U - y f
Preset no. I ' ' '--------
FM/AM + Listening
mode
i
Temporarily turning off the sound
To turn off the sound momentarily, press the
MUTING button on the remote controller. The
MUTING indicator will flash and the sound from
the speakers or headphones will be switched off
by the receiver’s audio muting circuit. Press the
MUTING button again to turn the sound back on.
Remote
controller
Flashes
I ' l l I T . I n w
45