Exo Terra Turtle Filter FX-200 / External Canister Filter User Manual

Page 3

Advertising
background image

4

1. The Exo Terra

®

Turtle Filter can either be placed next to terrarium

or else hung on the outside of the terrarium with the supplied

mounting bracket. When using the mounting bracket, use the

adjuster or adjust the height of the mounting bracket in order

to hang the unit in a vertical position. It is very important to the

proper operation of the filter that it be positioned vertically.

2. Pull the 4 cover locks outwards to unlock the filter cover. Pull

upwards on filter cover to remove it from the pump section.

Remove the filter baskets, and rinse the filtration media

thoroughly with clean and fresh water. After rinsing, replace the

filter baskets in position (see “Replacing Filtration Media” for

correct position).To clean the pump impeller: remove the pump

chamber (located on the underside of the filter cover). Remove

the impeller from the impeller well, and rinse under running

water. Check the impeller well for foreign matter, rinse if needed.

Replace the impeller, and reassemble the pump chamber.

3. Replace the filter cover on top of the pump section, ensure that

the 4 cover locks are in the“open” position (in outward position).

Press down firmly to ensure the filter cover is seated on the pump

section, and close the 4 covers locks until they click into position.

4. Check that the collet nuts on the inlet/outlet spigots (located on

top of the filter cover) are screwed all the way down to the bottom

of the spigot before attaching tubing. Attach tubing to spigot by

pushing tubing down on the spigot all the way to the topmost

thread. Then screw the collet nut upwards to compress and seal

the tubing onto the spigot.

5. Rotate the reservoir cap counter clock-wise to open (located on

top of the filter cover), and fill reservoir completely with water. To

close, replace and rotate cap clock-wise until it clicks.

6. Install filter in position. DO NOT plug it in.

7. Install Inlet Siphon Tube in a vertical position on the inside of the

tank, pressing firmly on the suction cups to ensure it will stick

to the glass. Install the Spray Bar in a horizontal position on the

inside of the tank, pressing firmly on the suction cups to ensure it

will stick to the glass. Attach the Inlet Siphon Tube and the Spray

Bar to the filter tubing by screwing the collet nut (located on

the end of the tubing) upwards to compress and seal the tubing

in place.

8. Before plugging in, ensure there are no bends or kinks in the

tubing. For best performance it is recommended to place the

filter in an upright vertical position at the same level as the tank.

Plug in filter.

Maintenance
NOTE: Failure to maintain filter may result in failure of the unit

and will invalidate your warranty.

To avoid injury, always unplug all appliances from the outlet

when not in use; before putting on or taking off parts; and before

cleaning. The motor is hermetically sealed, requiring no lubrication

or maintenance. Pull the 4 cover locks outwards to unlock the filter

cover. Pull upwards on filter cover to remove it from the pump

section.

an electrical socket. The drip loop is
that part of the cord below the level
of the socket or the connector if an
extension cord is used, to prevent
water travelling along the cord and
coming in contact with the socket. If
the plug or socket does get wet, DO
NOT unplug the cord. Disconnect the
fuse or circuit breaker that supplies
power to the appliance. Then unplug
and examine for presence of water in the socket.

3. This appliance is not intended for use by persons (including

children) with reduced physical sensory or mental capabilities, or

lack of experience or knowledge, unless a person responsible for

their safety has given them supervision or instruction concerning

use of the appliance. Children should be supervised to ensure

that they do not play with the appliance.

4. Always unplug an appliance from a socket when not in use,

before putting on or taking off parts, and before cleaning.

Never yank cord to pull plug from socket. Grasp the plug and

pull to disconnect.

5. To avoid injury do not contact moving parts or hot parts such as

heaters, impellers, lamp bulbs and the like.

6. Do not use an appliance for other than its intended use (i.e. do

not use in swimming pools, garden ponds, bathrooms or any

situations where people are immersed). The use of attachments

not recommended or sold by the manufacturer of the appliance

may cause an unsafe condition.

7. Do not install or store the appliance where it will be exposed to

the weather or to temperatures below freezing.

8. Make sure an appliance mounted on a tank is securely installed

before operating it.

9. Read and observe all the important notices on the appliance.

10. If an extension cord is necessary, a cord with a proper rating

should be used. A cord rated for less amperes or watts than the

appliance rating may overheat. Care should be taken to arrange

the cord so that it will not be tripped over or pulled.

SAVE THESE INSTRUCTIONS.

Only the faithful observation of these installation, electrical and

maintenance guidelines will ensure the safe and efficient use of

this appliance.

CAUTION

1. The Exo Terra

®

Turtle Filter is for indoor, household use only, and

for use with water not exceeding 35°C / 95°F. This filter is not

recommended or designed for use with corrosive or flammable

compounds or liquids with different properties other than water.

2. Be sure that the voltage of the mains supply corresponds to the

voltage shown on the rating label of the unit.

3. Before connecting to the mains supply ensure that the cord and

the unit are undamaged.

Installation (See illustrations on page 40)
Attention:
always unplug all electrical equipment, installed both

inside or outside the tank, from the mains supply before putting your

hands in the water or conducting any equipment maintenance.

ENGLISH

FRANÇAIS

DEUTSCH

ESP

AÑOL

IT

ALIANO

NEDERLANDS

Advertising