DMP Electronics Security Control Receiver SCS-1R - Manual (Page 28)

SCS-1R Installation Guide Digital Monitoring Products
23
OPERATOR’S GUIDE
SUBNET MASK:
255.255.255.000
Subnet Mask
Enter the SUBNET MASK assigned to the SCS-150. The default value is 255.255.255.000.
WEB USER NAME:
NEW
Web User Name
Enter a User Name for web programming access. This is the User Name entered to gain
access to the programming and can be up to 10 characters long. Default is NEW.
WEB PASSWORD:
NEW
Web Password
Enter the password to use for web programming access. This is the password used to gain
access to the programming and can be up to 10 characters long. Default is NEW.
Line Cards
This section assigns the line number and line type for all line cards connected to the SCS-150.
SCS-1R MENU
LINE CARDS
Line Cards
Press any top row Select key to assign the line number and line type for each line card
connected to the SCS-150.
CARD NUMBER: 1
Card Number
Press COMMAND to select the displayed Card Number to program. Press any top row
Select key to clear the display and enter a new card number. Enter the card number, 1
through 8, for which the communication method is to be specified.
Note: Lines 6-8 can only be used with SCS-104 Line Cards using SCS-150 Version 101 and
updated SCS-RACK hardware.
CARD NUMBER: 1
CARD MODEL: 104
Card Model
The display shows the current card model setting. Press any top row Select key to
change the Card Model. Press the Select key under the model for this card. Options
include NONE, 104, 101, and 100. Card number 1 defaults to Model 104. Card numbers
2-8 default to NONE.
SEND TIME CHANGE
TO PNLS? NO YES
Send Time Change
Press the top row Select key under YES to allow the SCS-1R to send time changes to
panels that communicate to the receiver on this line card. Select NO to prevent the
SCS-1R Receiver from sending time changes.
The following options display if 104 is selected as the Card Model.
Dialer Lines Setup
DIALER LINE 21
ENABLE? NO YES
Enable Dialer Lines
The card number is displayed first (Card 2 in the examples) followed by the line number
(Line 1 in the first example). Line numbers 1-4 represent dialer line cards for each card.
Press the far right Select key for YES, which enables dialer for the selected card and
line. After selecting, Line 2, 3 and 4 are displayed. Default is YES for all lines. If NO is
selected for all four lines, the dialer line setup prompts are skipped and the network
line setup prompts are displayed.
First Communication Type
Select DD to enable all dialer lines on the line card to communicate with panels using
digital dialer communication format. Select CID to enable all dialer lines on the line
card to communicate with panels using contact ID format. To change the
communication type, press any select key to display the options. Default is DD. If the
receiver cannot communicate with the panel using the first communication type, the
receiver attempts communication using the secondary communication type.
Second Communication Type
Select DD to enable all dialer lines on the line card to communicate with panels using
digital dialer communication format. Select CID to enable all dialer lines on the line
card to communicate with panels using contact ID format. Select NONE to have no
second communication type. To change the communication type, press any select key
to display the options. Default is DD.
SEND ANI/DNIS
INFO? NO YES
Send ANI/DNIS Information
Press the far right Select key for YES, which enables the Automatic Number
Identification (ANI) and Dialed Number Identification Service (DNIS) information to be
sent. ANI sends the phone number that the panel is using to call. DNIS sends the DNIS
identifier of the phone number that the panel dialed. Default is NO.
CARD NUMBER: 1
NONE 104 101 100
DIALER LINE 22
ENABLE? NO YES
DIALER LINE 23
ENABLE? NO YES
DIALER LINE 24
ENABLE? NO YES
FIRST COMM
TYPE: DD
FIRST COMM TYPE
DD CID
SECOND COMM
TYPE: DD
SECOND COMM TYPE
DD CID NONE