Avago Technologies LSI53C1000R User Manual

Avago Technologies Hardware

Advertising

DB14-000152-04

LSI53C1000R
PCI to Ultra160
SCSI Controller

TECHNICAL

MANUAL

A u g u s t 2 0 0 3

Version 2.2

Advertising

This manual is related to the following products:

LSI53C1000

Table of contents

Document Outline

Chapter1 Introduction
1.1 General Description
- Figure1.1 Typical LSI53C1000R Board Application
- Figure1.2 Typical LSI53C1000R System Application
1.2 Benefits of Ultra160 SCSI
1.3 Benefits of SURElink (Ultra160 SCSI Domain Validation) Technology
1.4 Benefits of LVDlink Technology
1.5 Benefits of TolerANT® Technology
1.6 Summary of LSI53C1000R Benefits
- 1.6.1 SCSI Performance
- 1.6.2 PCI Performance
- 1.6.3 Integration
- 1.6.4 Ease of Use
- 1.6.5 Flexibility
- 1.6.6 Reliability
- 1.6.7 Testability
Chapter2 Functional Description
- Figure2.1 LSI53C1000R Block Diagram
2.1 PCI Functional Description
- 2.1.1 PCI Addressing
- 2.1.2 PCI Bus Commands and Functions Supported
  - Table 2.1 PCI Bus Commands and Encoding Types
- 2.1.3 PCI Cache Mode
  - Table 2.2 PCI Cache Mode Alignment
2.2 SCSI Functional Description
- 2.2.1 SCRIPTS Processor
- 2.2.2 Internal SCRIPTS RAM
- 2.2.3 64Bit Addressing in SCRIPTS
- 2.2.4 Hardware Control of SCSI Activity LED
- 2.2.5 Designing an Ultra160 SCSI System
  - Table 2.3 New Phases on SCSI Bus
- 2.2.6 Prefetching SCRIPTS Instructions
- 2.2.7 Opcode Fetch Burst Capability
- 2.2.8 Load and Store Instructions
- 2.2.9 JTAG Boundary Scan Testing
- 2.2.10 Parity/CRC/AIP Options
  - Table 2.4 Bits Used for Parity/CRC/AIP Control and Generation
  - Table 2.5 SCSI Parity Errors and Interrupts
- 2.2.11 DMA FIFO
  - Figure2.2 DMA FIFO Sections
- 2.2.12 SCSI Data Paths
  - Figure2.3 LSI53C1000R Host Interface SCSI Data Paths
- 2.2.13 SCSI Bus Interface
  - Figure2.4 Regulated Termination for Ultra160 SCSI
- 2.2.14 Select/Reselect during Selection/Reselection
- 2.2.15 Synchronous Operation
  - Table 2.6 SCF Divisor Values
  - Figure2.5 Determining the Synchronous Transfer Rate
- 2.2.16 Interrupt Handling
- 2.2.17 Interrupt Routing
  - Figure2.6 Interrupt Routing Hardware Using the LSI53C1000R
- 2.2.18 Chained Block Moves
  - Figure2.7 Block Move and Chained Block Move Instructions
2.3 Parallel ROM Interface
- Table 2.7 Parallel ROM Support
2.4 Serial EEPROM Interface
- 2.4.1 Default Download Mode
  - Table 2.8 Default Download Mode Serial EEPROM Data Format
- 2.4.2 No Download Mode
2.5 Power Management
- Table 2.9 Power States
- 2.5.1 Power State D0
- 2.5.2 Power State D1
- 2.5.3 Power State D2
- 2.5.4 Power State D3
Chapter3 Signal Descriptions
3.1 Signal Organization
- Figure3.1 LSI53C1000R Signal Grouping
3.2 Internal Pull-ups and Pull-downs
- Table 3.1 LSI53C1000R Internal Pull-ups and Pull-downs
3.3 PCI Bus Interface Signals
- 3.3.1 System Signals
  - Table 3.2 System Signals
- 3.3.2 Address and Data Signals
  - Table 3.3 Address and Data Signals
- 3.3.3 Interface Control Signals
  - Table 3.4 Interface Control Signals
- 3.3.4 Arbitration Signals
  - Table 3.5 Arbitration Signals
- 3.3.5 Error Reporting Signals
  - Table 3.6 Error Reporting Signals
- 3.3.6 Interrupt Signals
  - Table 3.7 Interrupt Signals
3.4 SCSI Bus Interface Signals
- Table 3.8 SCSI Bus Interface Signals
- Table 3.9 SCSI Signals
- Table 3.10 SCSI Control Signals
3.5 General Purpose I/O (GPIO) Signals
- Table 3.11 GPIO Signals
3.6 Flash ROM and Memory Interface Signals
- Table 3.12 Flash ROM and Memory Interface Signals
3.7 Test Interface Signals
- Table 3.13 Test Interface Signals
3.8 Power and Ground Signals
- Table 3.14 Power and Ground Signals
3.9 MAD Bus Programming
- Table 3.15 MAD[3:1] Pin Decoding
Chapter4 Registers
4.1 PCI Configuration Registers
- Table 4.1 PCI Configuration Register Map
4.2 SCSI Registers
- Table 4.2 SCSI Register Map
- Table 4.3 Maximum Synchronous Offset
- Figure4.1 Single Transition Transfer Waveforms
- Figure4.2 DT Transfer Waveforms (XCLKS Examples)
- Figure4.3 DT Transfer Waveforms (XCLKH Examples)
- Table 4.4 DT Transfer Rates
- Table 4.5 Single Transition Transfer Rates
4.3 SCSI Shadow Registers
Chapter5 SCSI SCRIPTS Instruction Set
5.1 SCSI SCRIPTS
- Figure5.1 SCRIPTS Overview
5.2 Block Move Instructions
- 5.2.1 First Dword
  - Figure5.2 Block Move Instruction – First Dword
- 5.2.2 Second Dword
  - Figure5.3 Block Move Instruction – Second Dword
- 5.2.3 Third Dword
  - Figure5.4 Block Move Instruction – Third Dword
5.3 I/O Instructions
- 5.3.1 First Dword
  - Figure5.5 First 32Bit Word of the I/O Instruction
- 5.3.2 Second Dword
  - Figure5.6 Second 32Bit Word of the I/O Instruction
5.4 Read/Write Instructions
- 5.4.1 First Dword
  - Figure5.7 Read/Write Instruction – First Dword
- 5.4.2 Second Dword
  - Figure5.8 Read/Write Instruction – Second Dword
- 5.4.3 Read-Modify-Write Cycles
- 5.4.4 Move to/from SFBR Cycles
  - Table 5.1 Read/Write Instructions
5.5 Transfer Control Instructions
- 5.5.1 First Dword
  - Figure5.9 Transfer Control Instructions – First Dword
- 5.5.2 Second Dword
  - Figure5.10 Transfer Control Instructions – Second Dword
- 5.5.3 Third Dword
  - Figure5.11 Transfer Control Instructions – Third Dword
5.6 Memory Move Instructions
- Figure5.12 Memory Move Instructions – First Dword
- 5.6.1 Read/Write System Memory from a SCRIPT
- 5.6.2 Second Dword
  - Figure5.13 Memory Move Instructions – Second Dword
- 5.6.3 Third Dword
  - Figure5.14 Memory Move Instructions – Third Dword
5.7 Load and Store Instructions
- 5.7.1 First Dword
  - Figure5.15 Load and Store Instruction – First Dword
- 5.7.2 Second Dword
  - Figure5.16 Load and Store Instructions – Second Dword
Chapter6 Specifications
6.1 DC Characteristics
- Table 6.1 Absolute Maximum Stress Ratings
- Table 6.2 Operating Conditions
- Table 6.3 LVD Driver SCSI Signals – SD[15:0], SDP[1:0], SREQ/, SACK/, SMSG/, SIO/, SCD/, SATN/, S...
- Figure6.1 LVD Driver
- Table 6.4 LVD Receiver SCSI Signals – SD[15:0], SDP[1:0], SREQ/, SACK/, SMSG/, SIO/, SCD/, SATN/,...
- Figure6.2 LVD Receiver
- Table 6.5 DIFFSENS SCSI Signals
- Table 6.6 Input Capacitance
- Table 6.7 8 mA Bidirectional Signals – GPIO0_FETCH/, GPIO1_MASTER/, GPIO2, GPIO3, GPIO4
- Table 6.8 4 mA Bidirectional Signals – MAD[7:0]
- Table 6.9 4 mA Output Signals – MAS[1:0]/, MCE/, MOE/_TESTOUT, MWE/, TDO
- Table 6.10 8 mA PCI Bidirectional Signals – AD[63:0], C_BE[7:0]/, FRAME/, IRDY/, TRDY/, DEVSEL/, ...
- Table 6.11 Input Signals – CLK, GNT/, IDSEL, RST/, SCLK, TCK, TDI, TEST_HSC, TEST_RST/, TMS
- Table 6.12 8 mA Output Signals – INTA/, INTB/, ALT_INTA/, ALT_INTB/, REQ/, SERR/
6.2 TolerANT Technology Electrical Characteristics
- Table 6.13 TolerANT Technology Electrical Characteristics for SE SCSI Signals
- Figure6.3 Rise and Fall Time Test Condition
- Figure6.4 SCSI Input Filtering
- Figure6.5 Hysteresis of SCSI Receivers
- Figure6.6 Input Current as a Function of Input Voltage
- Figure6.7 Output Current as a Function of Output Voltage
6.3 AC Characteristics
- Table 6.14 External Clock
- Figure6.8 External Clock
- Table 6.15 Reset Input
- Figure6.9 Reset Input
- Table 6.16 Interrupt Output
- Figure6.10 Interrupt Output
6.4 PCI and External Memory Interface Timing Diagrams
- 6.4.1 Target Timing
- 6.4.2 Initiator Timing
- 6.4.3 External Memory Timing
6.5 SCSI Timing Diagrams
- Table 6.39 Initiator Asynchronous Send
- Figure6.35 Initiator Asynchronous Send
- Table 6.40 Initiator Asynchronous Receive
- Figure6.36 Initiator Asynchronous Receive
- Table 6.41 Target Asynchronous Send
- Figure6.37 Target Asynchronous Send
- Table 6.42 Target Asynchronous Receive
- Figure6.38 Target Asynchronous Receive
- Table 6.43 SCSI-1 Transfers (SE 5.0 Mbytes)
- Table 6.44 SCSI-2 Fast Transfers 10.0 Mbytes (8-Bit Transfers) or 20.0 Mbytes (16-Bit Transfers) ...
- Table 6.45 Ultra SCSI SE Transfers 20.0 Mbytes (8-Bit Transfers) or 40.0 Mbytes (16-Bit Transfers...
- Table 6.46 Ultra2 SCSI Transfers 40.0 Mbyte (8-Bit Transfers) or 80.0 Mbyte (16-Bit Transfers) Qu...
- Figure6.39 Initiator and Target ST Synchronous Transfer
- Table 6.47 SCSI-2 Fast Transfers 10.0 Mbytes (8-Bit Transfers) or 20.0 Mbytes (16-Bit Transfers) ...
- Table 6.48 Ultra SCSI SE Transfers 20.0 Mbytes (8-Bit Transfers) or 40.0 Mbytes (16-Bit Transfers...
- Table 6.49 Ultra2 SCSI Transfers 40.0 Mbyte (8-Bit Transfers) or 80.0 Mbyte (16-Bit Transfers) Qu...
- Table 6.50 Ultra160 SCSI Transfers 160 Mbyte (16-Bit Transfers) Quadrupled 40 MHz Clock
- Figure6.40 Initiator and Target DT Synchronous Transfer
6.6 Package Drawings
- Figure6.41 LSI53C1000R 456 BGA Chip – Top View
- Table 6.51 Alphanumeric List by Signal Name
- Table 6.52 Alphanumeric List by BGA Position
- Figure6.42 LSI53C1000R 456 BGA Mechanical Drawing
AppendixA Register Summary
- TableA.1 LSI53C1000R PCI Register Map
- TableA.2 LSI53C1000R SCSI Register Map
AppendixB External Memory Interface Diagram Examples
- FigureB.1 16 Kbyte Interface with 200 ns Memory
- FigureB.2 64 Kbyte Interface with 150 ns Memory
- FigureB.3 128, 256, 512 Kbyte or 1 Mbyte Interface with 150 ns Memory
- FigureB.4 512 Kbyte Interface with 150 ns Memory
Index
Customer Feedback

Popular Brands

Popular manuals