Stovax E-Studio PR0776 - Manual (Page 4)

4
USER INSTRUCTIONS
1. GENERAl
1.1 Installation and servicing must only be carried out by a
competent person.
1.2 In all correspondence, please quote the appliance type and
serial number, which can be found on the databadge
adjacent to the control knob.
1.3 Ensure that curtains are not positioned above the fire, and
that there is a 300mm minimum clearance between the
sides of the fire and any curtains.
1.4 This product is guaranteed for 2 years from the date of
installation, as set out in the terms and conditions of sale
between Gazco and your local Gazco dealer. Please consult
with your local Gazco dealer if you have any questions. In
all correspondence always quote the Model Number and
Serial Number.
1.5 Parts of this appliance become hot during normal use. It is
therefore recommended that a suitable fire guard be used
for protection of young children and the infirm.
1.6 If any cracks appear in the glass panel do not use the
appliance until the panel has been replaced.
2. lIGhTING ThE APPlIANCE
2.1 Locate the control valve on the appliance. There are two
control knobs on the valve, the right hand knob controls the
pilot ignition and the left hand knob controls the main
burner.
2.2 If your appliance has already been upgraded to battery
remote control, please refer to the instructions provided
with the upgrade to operate the remote control. The
following instructions will work for either situation.
1
AR0914
• Ensure that the left-hand control knob is pointing to off (
).
• Ensure that the right hand control knob is pointing to
off ( ).
• Press in the right hand control knob and rotate it anti-
clockwise until a click is heard (keep pressing in) and the
knob is pointing to pilot . The pilot should now light. If
the pilot has not lit, repeat the procedure until it
does.
• Keep the control knob pressed for 10 seconds and then
release it, the pilot should stay alight. If the pilot goes out,
repeat the procedures until it does.
2.3 If the pilot will not light after repeated attempts, contact the
retailer or installer from whom the appliance was
purchased.
• Turn the right-hand control to point to main burner .
The fire can now be controlled using the left-hand
control knob.
• Turn the left hand control knob to point to low fire ,
the main burner will light on low. The burner can
now be controlled between low and high settings. Turn the
control knob anticlockwise to increase the flame height and
clockwise to decrease the flame height.
3. TURNING ThE APPlIANCE OFF
3.1 To turn the fire off, locate the control valve, turn the left-
hand control knob until it points to off ( ). The main burner
will go out leaving the pilot burning.
3.2 To turn the pilot off, locate the control valve, turn the right
hand control knob until it points to off ( ), the pilot will
go out.
4. UPGRADING YOUR FIRE
4.1 Your fire is fitted with a control valve that can easily be
upgraded to battery powered remote control. This upgrade
can be fitted by anyone capable of simple DIY jobs and
requires no special training. This upgrade can be obtained
through your local Gazco stockist.
4.2 STANDARD REMOTE CONTROL This remote control can
control the fire after the pilot has been lit. It can turn the
main burner on and regulate it from low through to high
and back again. It can turn the main burner off leaving the
pilot burning GAZCO PART NUMBER 8455.
4.3 PROGRAMMABLE THERMOSTATIC AND TIMER REMOTE
CONTROL. This remote control can control the gas
appliance after the pilot has been lit. In MANUAL MODE it
can be used to turn the main burner on and manually
regulate it from low through to high and back again. It can
be used to turn the main burner off, leaving the pilot
burning. In AUTO MODE it will automatically regulate the
room temperature to a pre-set temperature. In